SOLUTION: WiFi connection Problem (specially office/univeristy network) - WPA + PEAP + MSCHAPv2
 

Here is the solution: Please follow the steps EXACTLY as below:
1. Select New Connection
2. Enter Connection Name
3. Scan for available wi-fi network - select "No" if it is hidden network
4. Enter the exact SSID (if it is hidden then select Hidden checkbox)
5. Network mode: Infrastructure
6. Security method: WPA with EAP (this is what I selected for connecting to my office network)
7. EAP Type: PEAP
8. Select Certificate: None
9. EAP Method: EAP MSCHAPv2
these are most important steps:::
10. User name: ONLY ENTER User Name - no domain is required here
11. Password: enter valid password
12. Click Next and then click "Advanced"
13. Click "EAP" tab
14. Select "Use manual user name" checkbox
15. Enter "Manual user name" as username@domain --- very important.
16. Save
17. Finish

You are all SET. Setps 10 to 15 are very important.
This is working like charm for me and I hope it works for you all...

Re: SOLUTION: WiFi connection Problem (specially office/univeristy network) - WPA + PEAP + MSCHAPv2
 

omg after hours of fighting, lectures and googling.... Your setup WORKS !!!
thanks very much, seems like the user@domain part is very important after all.

Re: SOLUTION: WiFi connection Problem (specially office/univeristy network) - WPA + PEAP + MSCHAPv2
 

Funny, for me it always did without the domain.

Re: SOLUTION: WiFi connection Problem (specially office/univeristy network) - WPA + PEAP + MSCHAPv2
 

my school specially stated about the user@domain part, I just didn't know where to put it, perhaps it's important only for eduroam and uni .

Re: SOLUTION: WiFi connection Problem (specially office/univeristy network) - WPA + PEAP + MSCHAPv2
 

It says the certificate isn't valid.

Re: SOLUTION: WiFi connection Problem (specially office/univeristy network) - WPA + PEAP + MSCHAPv2
 

I get "can't authenticate"? I know the username and pw are correct? It does however recognize the network now. Before it wouldn't see it.

And sometimes with the same settings I get "something's wrong with the network connection"

Re: SOLUTION: WiFi connection Problem (specially office/univeristy network) - WPA + PEAP + MSCHAPv2
 

For me it works with DOMAIN\user in both steps 10 and 15 (manual user name still required even though identical to the regular user name).

Re: SOLUTION: WiFi connection Problem (specially office/univeristy network) - WPA + PEAP + MSCHAPv2
 

hi..i have updated to Pr 1.1 and i have used the following configurations to connect to my university's wlan network but i still get the same message over and over again, which is "Something's wrong with the network connection" while my laptop and everybody else can connect to the wlan network perfectly..

Typed in the wlan's name for the connection and network name(SSID)
Use automatically: yes/no (no difference)
Network mode: Infrastructure
Security method: WPA EAP
WPA EAP type: PEAP
Select certificate: None
EAP method: EAP MSCHAPv2
Username: <username>
Password: <password>

Advanced Settings:
Proxy configuration: No proxy
Auto-retrieve IP address: on
Auto-retrieve DNS address: on
Manuall username: on/off (no difference)
Username: same as the username above
Require client authentication: off
WPA2 only mode: on/off (no difference)

please help me..

Re: SOLUTION: WiFi connection Problem (specially office/univeristy network) - WPA + PEAP + MSCHAPv2
 

ErrorInDisplay

I got it to work by configuring username differently in Advanced page, so if your username is user it would be:

username: user
password: your_pass

advanced-wpa eap
Manual username ON
username: user@school.domain (ie. user@uni.com)

Re: SOLUTION: WiFi connection Problem (specially office/univeristy network) - WPA + PEAP + MSCHAPv2
 

Kozzi

Thanks but i'm still getting the "Something's wrong with the network connection" message..