DIY Cheap MicroSD to RS-MMC converter in 15 minutes.
 

That's what I've done for my 'new' n770.
I bought cheapest Kingston's MicroSD card which came with two converters - MicroSD-MiniSD (needed for my n810) and 'spare' MicroSD-SD.
You can say that I should simply buy another RS-MMC 2GB card and forget all the trouble but - I needed this converter for n810 and... this was 1$ cheaper solution :)

First - I dissassembled MicroSD-SD converter - it's easy with sharp knife since it's not glued for this specific type.
Once You open one - You can see connectors fixed with little plastic bar.
Connectors are delicate so It's not good idea to throw away supporting plate (on the left).
http://xtcnow.w.interia.pl/gfx/IMG_0002.JPG

The idea was to cut space for microsd card in this supporting part.
On photo below You can see connectors glued with UHU to cut supporting plate (glue between support and connector's plastic bar).
http://xtcnow.w.interia.pl/gfx/IMG_0004.JPG

Below You can see how it looks from the other side.
http://xtcnow.w.interia.pl/gfx/IMG_0005.JPG

Contacts need to be straightened and bent to the 'other side'.
http://xtcnow.w.interia.pl/gfx/IMG_0014.JPG

Below it's a test - pins not bent to their final position.
As You can see - card placement is good enough.
http://xtcnow.w.interia.pl/gfx/IMG_0015.JPG

Then - when making them more twisted - card locks itself in.
They are elastic spring contact so it's easy to push the card downward at it's end to get good connection at all contacts.
http://xtcnow.w.interia.pl/gfx/IMG_0016.JPG

Now to position the card I cut a part of plastic from card's blister.
It's bit too thick though.
http://xtcnow.w.interia.pl/gfx/IMG_0017.JPG

Now - glue this cover.
http://xtcnow.w.interia.pl/gfx/IMG_0018.JPG

And for the final touch - isolate connectors using some transparent adhesive tape.
http://xtcnow.w.interia.pl/gfx/IMG_0019.JPG
http://xtcnow.w.interia.pl/gfx/IMG_0020.JPG

Voila.
I'm using Fanoush's high speed sdhc enabled kernel so any available MicroSD card will do.
It's bit thicker than RSMMC card - mainly because of my transparent plastic cover.
I was able to place it in n770's slot with no problem from the first time.
Of'course one can say that it's not elegant and doesn't survive many plugin cycles but c'mon - it's cheap, fast and with nothing to loose as long as You dont short connector pins.
Feel free to modify.

Re: DIY Cheap MicroSD to RS-MMC converter in 15 minutes.
 

Brilliant! With a little soldering between the pins and card, that connection could become very permanent and reliable. Although it might have to be a pretty low wattage soldering iron.

Frank

Re: DIY Cheap MicroSD to RS-MMC converter in 15 minutes.
 

I already see my 770 returning in its full glory... :)

Re: DIY Cheap MicroSD to RS-MMC converter in 15 minutes.
 

Believe me, spring contact form very good connection. Not all contacts are needed in fact but I choose not to select them.
I considered soldering at the first thougts but there's no need for damaging gold plated contacts on the card itself - at least for me.
I even considered direct card to pcb soldering in case I don't find less brutal solution.

Re: DIY Cheap MicroSD to RS-MMC converter in 15 minutes.
 

Wow. Very innovative. Great pictures. You also must have the hands of a surgeon!

Re: DIY Cheap MicroSD to RS-MMC converter in 15 minutes.
 

Great! I had only planned to find out whether the microsd-sd adapter could be utilized for 770 RS-MMC slot, so thanks for saving me time. Now it is time to search for cheap microSD cards:)

Re: DIY Cheap MicroSD to RS-MMC converter in 15 minutes.
 

Thanks for the information. Anyone knows if OS 2006 can be installed on the microSD card? If so, any instructions?

Re: DIY Cheap MicroSD to RS-MMC converter in 15 minutes.
 

I'd assume that you'd install it in the same way as you'd do it on an MMC. The kernel is installed on flash memory, so as long as you use Fanoush's SDHC kernel it will boot fine.

I'm just ordered myself an 8GB Class-6 MicroSDHC from 7dayshop.com for just under £11. It comes with an adapter, too. Looking forward to the upgrade!

Re: DIY Cheap MicroSD to RS-MMC converter in 15 minutes.
 

I didn't succeed in creating one :( yet... :)

Re: DIY Cheap MicroSD to RS-MMC converter in 15 minutes.
 

IMO the most tricky part is to maintain support for gold connector plates of disassembled converter.
That's why I didn't cut this one from edge to edge - I've left these little plastic forms that supported connector plates in oryginal design.
Maybe it would help to glue plates at their's back to these supporting plastic stands.