[ 158.265625] tusb_source_power 633: VBUS a_wait_vrise, devctl 5d otg 171 conf c0010000 prcm 00a80500[ 158.265625] musb_stage0_irq 645: CONNECT (a_host) devctl 5d [ 158.289062] hub 1-0:1.0: state 8 ports 1 chg 0000 evt 0000 [ 158.289062] usb usb1: usb auto-resume [ 158.289062] usb usb1: finish resume [ 158.289062] hub 1-0:1.0: hub_resume [ 158.312500] hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s [ 158.539062] hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 [ 158.664062] usb 1-1: new full speed USB device using musb_hdrc and address 2 [ 158.804687] usb 1-1: ep0 maxpacket = 8 [ 158.804687] usb 1-1: skipped 3 descriptors after interface [ 158.804687] usb 1-1: default language 0x0409 [ 158.804687] usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=220 [ 158.804687] usb 1-1: Manufacturer: Arduino (www.arduino.cc) [ 158.804687] usb 1-1: SerialNumber: A4139373630351600151 [ 158.804687] usb 1-1: device v2341 p0043 is not supported [ 158.804687] usb 1-1: uevent [ 158.804687] usb 1-1: usb_probe_device [ 158.804687] usb 1-1: configuration #1 chosen from 1 choice [ 158.804687] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 158.804687] usb 1-1:1.0: uevent [ 158.804687] usbserial_generic 1-1:1.0: usb_probe_interface [ 158.804687] usbserial_generic 1-1:1.0: usb_probe_interface - got id [ 158.804687] usbtest 1-1:1.0: usb_probe_interface[ 158.804687] usbtest 1-1:1.0: usb_probe_interface - got id [ 158.812500] usb 1-1: adding 1-1:1.1 (config #1, interface 1) [ 158.812500] usb 1-1:1.1: uevent [ 158.812500] usbserial_generic 1-1:1.1: usb_probe_interface [ 158.812500] usbserial_generic 1-1:1.1: usb_probe_interface - got id [ 158.812500] usbtest 1-1:1.1: usb_probe_interface[ 158.812500] usbtest 1-1:1.1: usb_probe_interface - got id [ 158.812500] /home/dvondle/maemo_kernel/kernel-source-diablo-2.6.21/kernel-source/drivers/usb/core/inode.c: creating file '002' [ 158.812500] hub 1-0:1.0: 100mA power budget left[ 158.812500] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002 [ 158.812500] hub 1-0:1.0: port 1 enable change, status 00000103 [ 160.812500] usb 1-1: usb auto-suspend [ 162.835937] hub 1-0:1.0: hub_suspend [ 162.835937] usb usb1: usb auto-suspend