Ok. Also think so. Btw, flashed w/o any problems. Now, it's fully working DevKit. Btw, will post photo of F1's HW from thread above soon. Just for history and base of N950 HW knowledge.

IMPORTANT: READ THIS CAREFULLY AS BY DOWNLOADING, INSTALLING AND/OR USING
THE NOKIA N950 ONECLICKFLASHER┬нIMAGE YOU ACKNOWLEDGE AND AGREE TO THE
FOLLOWING TERMS AND CONDITIONS:

1) The NOKIA N950 ONECLICKFLASHER┬нIMAGE comprises of
a) some software copyrighted by Nokia Corporation or third
parties in binary form (collectively Licensed Software) and/or
b) Open Source Software.

2) Licensed Software is distributed to you only in binary form. You
a) are authorized to use the Licensed Software only in or in
connection with the Nokia N950-products; and
b) may not use, modify, adapt, translate, copy and/or distribute
Licensed Software, except as expressly permitted herein.

3) The NOKIA N950 ONECLICKFLASHER┬нIMAGE is provided to you AS IS
and Nokia, its affiliates and/or its licensors do not make any
representations or warranties, express or implied (including, without
any limitation, the warranties of merchantability or fitness for
a particular purpose, or that it will not infringe any third party
patents, copyrights, trademarks or other rights).
You agree that any downloading, installation and/or use by you of
the NOKIA N950 ONECLICKFLASHER┬нIMAGE happens and is solely at your
own risk and that Nokia assumes no liability whatsoever for any
damages that you may incur or suffer in connection with the
NOKIA N950 ONECLICKFLASHER┬нIMAGE and/or the installation or use
thereof.

4) The Open Source Software is licensed and distributed under the
applicable open source/free software licenses and/or other licenses,
permissions, notices or disclaimers containing obligation or
permission to provide the source code of such software. The relevant
source code of the Open Source Software is made available to you
per the product loan agreement you have concluded with us for the
Nokia 950.
Press Y <Ret> if your accept terms, any other key to decline y
Installed version 7.1.41, file version 7.1.41

Please make sure your device is properly powered OFF prior to connecting
the USB cable. You can power your device off by holding down the power
button for 8+ seconds.

Flashing your device will erase all data and reset the device back to
factory state. Please make sure you have backups of your data before
proceeding with flashing.

If flashing does not start disconnect the USB cable from the device, make
sure the device is OFF and then reconnect the device with the USB cable.
For first flashing you may need to repeat this a few times.
Depending on amount of data to be securely erased, the erasing may take as long
as 30
minutes until the flashing starts. Please, be patient.


Check first that device is powered OFF and then connect USB cable.

First erasing eMMC
Then flashing image and eMMC
Flashing started at 16.05.2015 17:17:43,82

flasher 3.12.1 (Oct 6 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

Suitable USB interface (bootloader/phonet) not found, waiting...
Found device RM-680, hardware revision 0829
NOLO version 2.0.36
Version of 'sw-release': DFL61_HARMATTAN_0.2011.21-1_RD_001
Sending ape-algo image (7096 kB)...
100% (7096 of 7096 kB, avg. 35658 kB/s)
Suitable USB interface (phonet) not found, waiting...
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-680 rev. 0829
Server implements softupd protocol version 1.8

Battery level 90 %, continuing.
Erasing, this may take a while.
Erase done.
Image SW version DFL61_HARMATTAN_3.2012.02-6_PR_RM680
Image moslo not present
Image tar skipped
Image config skipped

Battery level 91 %, continuing.

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[x] cmt-mcusw [finished 100 % 6008 / 6008 kB 3133 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 2535 kB/s]
[x] rootfs [finished 100 % 758715 / 758715 kB 10183 kB/s]
[x] mmc [finished 100 % 172719 / 172719 kB 18619 kB/s]
Updating SW release
Success
Status: 0
Flashing ended at 16.05.2015 17:21:22,74
Press Enter to exit
Unplug the USB cable from the device to boot new flashed image ...