Reply
Thread Tools
Posts: 126 | Thanked: 160 times | Joined on Aug 2012
#1
After charging the battery and disconnected the charger, still shows me loading and stays constantly green LED. When the cell is switched off, the device draws 0.35A (350mA) from battery.

Nokia-N900:~# hal-device bme
udi = '/org/freedesktop/Hal/devices/bme'
info.addons = { 'hald-addon-bme' } (string list)
battery.type = 'pda' (string)
info.subsystem = 'unknown' (string)
info.product = 'Battery (BME-HAL)' (string)
info.udi = '/org/freedesktop/Hal/devices/bme' (string)
battery.reporting.unit = 'mAh' (string)
battery.present = true (bool)
battery.voltage.current = 4058 (0xfda) (int)
battery.is_rechargeable = true (bool)
battery.rechargeable.is_charging = true (bool)
battery.rechargeable.is_discharging = true (bool)
battery.reporting.current = 1388 (0x56c) (int)
battery.reporting.last_full = 1277 (0x4fd) (int)
battery.charge_level.current = 8 (0x8) (int)
battery.charge_level.last_full = 8 (0x8) (int)
battery.charge_level.design = 8 (0x8) (int)
battery.charge_level.percentage = 100 (0x64) (int)
battery.voltage.design = 4200 (0x1068) (int)
battery.charge_level.capacity_state = 'full' (string) - ?
battery.voltage.unit = 'mV' (string)
battery.charge_level.unit = 'bars' (string)
info.category = 'battery' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.capabilities = { 'battery' } (string list)
battery.reporting.design = 1277 (0x4fd) (int)
battery.remaining_time = 51480 (0xc918) (int)
battery.remaining_time.calculate_per_time = false (bool)
maemo.charger.connection_status = 'connected' (string) - ?
maemo.charger.type = 'host 500 mA' (string) - ?
maemo.rechargeable.charging_status = 'full' (string) - ?
maemo.rechargeable.positive_rate = true (bool)
maemo.bme.version = '1.0' (string)
What's the problem?
 
Posts: 986 | Thanked: 1,526 times | Joined on Jul 2010
#2
see the problem there is your harjukan is crossed with your pubricator. open er up, eat the battery, bathe er in whiskey, and hang er on a clothesline til mornin.
__________________
~ teleshoes ~
 
Posts: 986 | Thanked: 1,526 times | Joined on Jul 2010
#3
1) replace the battery, see if your love problem goes away
2) disconnect the battery, screen, and delicate peripherals, e.g.: camera
3) spray alcohol on the exposed board and vulnerable, sensitive contacts
4) gently explore its inner surfaces with cotton swabs
__________________
~ teleshoes ~
 
Posts: 126 | Thanked: 160 times | Joined on Aug 2012
#4
These plastic parts, such as the camera and seals. Everything would be distorted and matte did.
 
Posts: 986 | Thanked: 1,526 times | Joined on Jul 2010
#5
naw .
__________________
~ teleshoes ~
 
Posts: 986 | Thanked: 1,526 times | Joined on Jul 2010
#6
use rubbing alcohol, not moonshine, and spray it on the cotton swabs instead like normal first. then try using moaaarrrrr. but really, replace the battery first. theyre cheap and a spare is always good to have
__________________
~ teleshoes ~
 
Posts: 126 | Thanked: 160 times | Joined on Aug 2012
#7
I did everything I bought new batteries.
I bought the cell on an auction and it was defected.
At the beginning it was the worst. It restarted after switching off and I couldn't run it properly. The only way to switch it on was a little trick I have teached. I reflashed it, took over the cover, cleaned the mainboard and after it I dryed it with a hairdryer. In the end it was better, there was no restarts. The cell worked awhile without any problems. Then again, I had problems just with running. Now, after applying BME Replacement appeared a new problem. After disconectig from the charger the LED stays constantly green.

Last edited by pinochio; 2013-10-24 at 20:36.
 
Reply

Thread Tools

 
Forum Jump


All times are GMT. The time now is 12:21.