/dev/mmcblk0p1 aka /home/user/MyDocs not mounted after re-boot? - maemo.org

Active Topics

Is there a section to talk about Java ME? Apps, etc. (3)
to General by Kalatti - 23 hrs, 26 mins ago
more...

Thread Tools

zimon	2010-04-28 , 12:25
Posts: 1,341 \| Thanked: 708 times \| Joined on Feb 2010	#1

I have noticed few times, (if not always) rebooting with power-menu "Reboot"-command leaves /dev/mmcblk0p1 unmounted. I need to manually mount it.

Just awhile ago again:

Code:

Nokia-N900-42-11:~# df -h /home/user/MyDocs
Filesystem                Size      Used Available Use% Mounted on
/dev/mmcblk0p2            2.0G    713.4M      1.2G  37% /home
Nokia-N900-42-11:~# mount /home/user/MyDocs
Nokia-N900-42-11:~# df -h /home/user/MyDocs
Filesystem                Size      Used Available Use% Mounted on
/dev/mmcblk0p1           27.0G      5.8G     21.2G  22% /home/user/MyDocs

(from time_in_state.sh):
Uptime:              17 min
Load:                0.16, 0.25, 0.48
Boot reason:         sw_rst

Nokia-N900-42-11:~# dmesg
....
[76766.307464] OneNAND version = 0x0121
[76766.307495] Chip support all block unlock
[76766.307495] Chip has 2 plane
[76766.309112] Scanning device for bad blocks
[76766.378112] onenand_bbt_wait: ecc error = 0x2222, controller error 0x2400
[76766.378143] Bad eraseblock 1205 at 0x096a0000
[76766.426391] Creating 6 MTD partitions on "omap2-onenand":
[76766.426422] 0x00000000-0x00020000 : "bootloader"
[76766.426818] 0x00020000-0x00080000 : "config"
[76766.427062] 0x00080000-0x000c0000 : "log"
[76766.429565] mtdoops: Ready 9, 10 (no erase)
[76766.429595] mtdoops: Attached to MTD device 2
[76766.429626] 0x000c0000-0x002c0000 : "kernel"
[76766.429901] 0x002c0000-0x004c0000 : "initfs"
[76766.430145] 0x004c0000-0x10000000 : "rootfs"
[76766.432159] UBI: attaching mtd5 to ubi0
[76766.432189] UBI: physical eraseblock size:   131072 bytes (128 KiB)
[76766.432220] UBI: logical eraseblock size:    129024 bytes
[76766.432281] UBI: smallest flash I/O unit:    2048
[76766.432312] UBI: sub-page size:              512
[76766.432312] UBI: VID header offset:          512 (aligned 512)
[76766.432373] UBI: data offset:                2048
[76766.566131] UBI: attached mtd5 to ubi0
[76766.566192] UBI: MTD device name:            "rootfs"
[76766.566223] UBI: MTD device size:            251 MiB
[76766.566253] UBI: number of good PEBs:        2009
[76766.566284] UBI: number of bad PEBs:         1
[76766.566314] UBI: max. allowed volumes:       128
[76766.566345] UBI: wear-leveling threshold:    4096
[76766.566375] UBI: number of internal volumes: 1
[76766.566406] UBI: number of user volumes:     1
[76766.566436] UBI: available PEBs:             0
[76766.566467] UBI: total number of reserved PEBs: 2009
[76766.566497] UBI: number of PEBs reserved for bad PEB handling: 20
[76766.566528] UBI: max/mean erase counter: 124/34
[76766.566558] UBI: image sequence number: 1
[76766.567077] usbcore: registered new interface driver libusual
[76766.567169] UBI: background thread "ubi_bgt0d" started, PID 26
[76766.587249] input: omap_twl4030keypad as /class/input/input1
[76766.635833] cpuidle: using governor ladder
[76766.635894] cpuidle: using governor menu
[76766.636077] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
[76766.636322] ASoC version 0.13.2
[76766.650054] AIC3X Audio Codec 0.2
[76766.652587] asoc: tlv320aic3x <-> omap-mcbsp-dai-0 mapping ok
[76766.654113] asoc: Bluetooth codec <-> omap-mcbsp-dai-1 mapping ok
[76766.705657] input: RX51 (tlv320aic3x) Jack as /class/input/input2
[76766.729949] ALSA device list:
[76766.729980]   #0: RX51 (tlv320aic3x)
[76766.730499] TCP cubic registered
[76766.730560] NET: Registered protocol family 17
[76766.730621] NET: Registered protocol family 15
[76766.730682] Power Management for TI OMAP3.
[76766.734069] pm_dbg_init()
[76766.734802] SmartReflex driver initialized
[76766.741485] Disabling unused clock "gpt2_ick"
[.....deleted...]
[76766.743316] Disabling unused clock "dpll3_m3x2_ck"
[76766.743682] Bootup reason: sw_rst
[76766.743774] OMAP GPIO switch handler initializing
[76766.746459] slide (GPIO 71) is now closed
[76766.746490] proximity (GPIO 89) is now open
[76766.746520] kb_lock (GPIO 113) is now open
[76766.746551] headphone (GPIO 177) is now disconnected
[76766.746582] cam_shutter (GPIO 110) is now open
[76766.746612] cam_launch (GPIO 69) is now inactive
[76766.746643] cam_focus (GPIO 68) is now inactive
[76766.746673] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
[76766.766632] omapfb: acx565akm rev 8d LCD detected
[76766.776275] tpa6130a2 2-0060: Headphone amplifier initialized successfully
[76766.824645] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[76766.824707] UBIFS: file system size:   254693376 bytes (248724 KiB, 242 MiB, 1974 LEBs)
[76766.824768] UBIFS: journal size:       9033728 bytes (8822 KiB, 8 MiB, 71 LEBs)
[76766.824829] UBIFS: media format:       4 (latest is 4)
[76766.824859] UBIFS: default compressor: lzo
[76766.824890] UBIFS: reserved for root:  4384586 bytes (4281 KiB)
[76766.825439] VFS: Mounted root (ubifs filesystem).
[76766.825653] Freeing init memory: 144K
[76768.227874] Registered led device: twl4030:vibrator
[76768.360809] twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
[76768.469421] tsl2563 2-0029: model 7, rev. 0
[76768.545928] lp5523 2-0032: LP5523 Programmable led chip found
[76768.612762] Linux video capture interface: v2.00
[76768.715881] I2C driver for Si4713 FM Radio Transmitter
[76769.474700] Bluetooth: Core ver 2.15
[76769.493194] NET: Registered protocol family 31
[76769.493255] Bluetooth: HCI device and connection manager initialized
[76769.493286] Bluetooth: HCI socket layer initialized
[76769.539978] i2c_omap i2c_omap.2: controller timed out
[76769.540283] hci_h4p hci_h4p: Registering HCI H4P device
[76769.596832] lp5523 2-0032: got interrupt from led chip
[76769.597381] lp5523 2-0032: interrupt from led chip 4f
[76769.597412] lp5523 2-0032: all engines configured
[76769.597442] lp5523 2-0032: disabling engines
[76769.598052] Registered led device: lp5523:kb1
[76769.598236] Registered led device: lp5523:kb2
[76769.598358] Registered led device: lp5523:kb3
[76769.598510] Registered led device: lp5523:kb4
[76769.598663] Registered led device: lp5523:b
[76769.598785] Registered led device: lp5523:g
[76769.598907] Registered led device: lp5523:r
[76769.599060] Registered led device: lp5523:kb5
[76769.599182] Registered led device: lp5523:kb6
[76769.640472] nokia-av nokia-av: accessory detect module initialized
[76769.681854] radio-si4713 2-0063: Detected Si4713 (0x0d) Firmware: 3.0 Patch ID: 00:00 Component: 3.0 Chip Rev.: unknown
[76769.725067] TSC2005 driver initializing
[76769.725769] input: TSC2005 touchscreen as /class/input/input3
[76769.730743] mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
[76769.837280] mmci-omap-hs mmci-omap-hs.1: Failed to get debounce clock
[76769.965057] omap_wdt omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec, nowayout is on
[76769.992462] SSI DRIVER Version 1.1-rc2
[76769.998901] omap_ssi omap_ssi: SSI Hardware REVISION 1.0
[76770.097900] phy0: Selected rate control algorithm 'minstrel'
[76770.123474] smc91x: not found (-19).
[76770.143249] wl1251: loaded
[76770.143981] wl1251: initialized
[76770.149322] mmc0: host does not support reading read-only switch. assuming write-enable.
[76770.149414] mmc0: new high speed SD card at address b368
[76770.157531] mmcblk0: mmc0:b368 UD    968 MiB 
[76770.157867]  mmcblk0: p1
[76770.352539] mmc1: new high speed MMC card at address 0001
[76770.363739] mmcblk1: mmc1:0001 MMC32G 29.8 GiB 
[76770.364074]  mmcblk1: p1 p2 p3
[76770.518524] CMT speech driver v0.2.0
[76770.524108] NET: Registered protocol family 35
[76770.555145] SSI McSAAB PROTOCOL Version: 2.0-rc1
[76770.560424] McSAAB: ACWAKE DOWN
[76770.560516] McSAAB: ACWAKE UP
[76770.560577] McSAAB: WAKELINES TEST OK
[76770.947723] dspbridge_init: 412800 bytes @ 80600000
[76771.026123] omap-iommu omap-iommu.1: isp registered
[76771.190277] omap-iommu omap-iommu.1: isp: version 1.1
[76771.339569] smia-sensor 2-0010: firmware: requesting smia-sensor-01-022b-04.bin
[76771.365478] smia_reglist_import: meta_reglist version 2009-07-27
[76771.365539] smia_reglist_import: type 10	w 648	h 488	fmt 30314142	ival 100/1502	ptr d0cbc2a0
[76771.365570] smia_reglist_import: type 10	w 648	h 488	fmt 30314142	ival 100/3003	ptr d0cbc228
[76771.365600] smia_reglist_import: type 1	w 0	h 0	fmt 30314142	ival 100/0	ptr d0cbc090
[76771.365600] smia_reglist_import: type 0	w 0	h 0	fmt 30314142	ival 100/0	ptr d0cbc038
[76771.377319] et8ek8 3-003e: firmware: requesting et8ek8-0002.bin
[76771.401824] smia_reglist_import: meta_reglist version V14 03-June-2008
[76771.401916] smia_reglist_import: type 10	w 2592	h 1968	fmt 30314442	ival 100/1292	ptr d0cbf1f4
[76771.401947] smia_reglist_import: type 10	w 2592	h 1968	fmt 30314142	ival 100/399	ptr d0cbf454
[76771.401947] smia_reglist_import: type 10	w 1296	h 984	fmt 30314142	ival 100/501	ptr d0cbf57c
[76771.401977] smia_reglist_import: type 10	w 1296	h 984	fmt 30314442	ival 100/2500	ptr d0cbf614
[76771.401977] smia_reglist_import: type 10	w 1296	h 984	fmt 30314442	ival 100/3000	ptr d0cbf28c
[76771.402008] smia_reglist_import: type 10	w 864	h 656	fmt 30314142	ival 100/2988	ptr d0cbf324
[76771.402038] smia_reglist_import: type 10	w 648	h 492	fmt 30314142	ival 100/499	ptr d0cbf4e4
[76771.402038] smia_reglist_import: type 10	w 648	h 492	fmt 30314142	ival 100/2993	ptr d0cbf3bc
[76771.402069] smia_reglist_import: type 1	w 2592	h 1968	fmt 30314142	ival 100/1207	ptr d0cbf04c
[76772.392883] g_file_storage gadget: File-backed Storage Gadget, version: 7 August 2007
[76772.392944] g_file_storage gadget: Number of LUNs=2 Number of buffers=16
[76772.393005] musb_hdrc musb_hdrc: MUSB HDRC host driver
[76772.393585] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
[76772.394042] usb usb1: configuration #1 chosen from 1 choice
[76772.394256] hub 1-0:1.0: USB hub found
[76772.394348] hub 1-0:1.0: 1 port detected
[76783.162170] kjournald starting.  Commit interval 1 seconds
[76783.177062] EXT3 FS on mmcblk1p2, internal journal
[76783.177093] EXT3-fs: mounted filesystem with writeback data mode.
[76783.526336] Adding 786424k swap on /dev/mmcblk0p3.  Priority:-1 extents:1 across:786424k
[76784.117340] Bluetooth: L2CAP ver 2.13
[76784.117370] Bluetooth: L2CAP socket layer initialized
[76784.213226] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[76784.213256] Bluetooth: BNEP filters: protocol multicast
[76784.381103] Bluetooth: SCO (Voice Link) ver 0.6
[76784.381134] Bluetooth: SCO socket layer initialized
[76784.387359] hci_h4p hci_h4p: firmware: requesting bcmfw.bin
[76784.955383] Bluetooth: RFCOMM socket layer initialized
[76784.955505] Bluetooth: RFCOMM TTY layer initialized
[76784.955505] Bluetooth: RFCOMM ver 1.11
[76788.841156] misc iphb: Module registered in 2.6.28-omap1, built Dec 17 2009 09:42:15
[76815.875854] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76817.780670] warning: `dnsmasq' uses 32-bit capabilities (legacy support in use)
[76827.651885] cfg80211: Regulatory domain changed to country: EU
[76827.651916] 	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[76827.651947] 	(2402000 KHz - 2482000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[76827.651947] 	(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[76827.651977] 	(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[76827.651977] 	(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[76827.652008] 	(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[76827.652008] 	(5490000 KHz - 5710000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[76827.696594] wl12xx spi4.0: firmware: requesting wl1251-fw.bin
[76828.261962] SCSI subsystem initialized
[76829.204162] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[76829.219787] wl1251: firmware booted (Rev 4.0.4.3.7)
[76829.244812] Driver 'sd' needs updating - please use bus_type methods
[76830.860565] wl1251: down
[76831.383850] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[76831.399475] wl1251: firmware booted (Rev 4.0.4.3.7)

[76834.648925] wlan0: associated
[76836.136993] wlan0: roaming signal from driver, sending LOWSIGNAL
[76839.011901] wlan0: driver reports beacon loss from AP cf1bb52c - sending probe request
[76843.836822] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76848.829010] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76858.133636] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76866.360290] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76871.079010] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76880.602478] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76883.968353] wlan0: driver reports beacon loss from AP cf1bb52c - sending probe request
[76885.985321] wlan0: no probe response from AP cf1bb52c - disassociating
[76887.446228] wlan0: authenticate with AP 00:1e:4a:bd:f6:71
[76887.462554] wlan0: authenticated
[76887.462585] wlan0: associate with AP 00:1e:4a:bd:f6:71
[76887.472137] wlan0: RX AssocResp from 00:1e:4a:bd:f6:71 (capab=0x421 status=0 aid=1)
[76887.472167] wlan0: associated
[76896.345916] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76899.870819] regulator_disable: not in use by this consumer
[76899.870849] regulator_disable: not in use by this consumer
[76900.305664] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76929.941162] wlan0: roaming signal from driver, sending LOWSIGNAL
[76943.102691] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76944.438507] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76947.738311] wlan0: deauthenticating by local choice (reason=3)
[76947.907806] wl1251: down
[76958.189666] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76974.797973] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[76979.165100] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[77049.430572] HWRecoveryResetSGX: SGX Hardware Recovery triggered
[77468.696502] kb_lock (GPIO 113) is now closed
[77468.868347] kb_lock (GPIO 113) is now open
[77531.922698] HWRecoveryResetSGX: SGX Hardware Recovery triggered

Is this a known bug?

(Yes I know, "Reboot" is not enabled by default in the powermenu of N900, so it may be a known bug.)

Last edited by zimon; 2010-05-26 at 17:30. Reason: syslog replaced with dmesg output

Quote & Reply |

zimon	2010-05-26 , 16:17
Posts: 1,341 \| Thanked: 708 times \| Joined on Feb 2010	#2

This bug manifests also with HealthCheck program when using its reboot-tool.

Quote & Reply |

	noobmonkey	2010-05-26 , 17:27
	Posts: 3,203 \| Thanked: 1,391 times \| Joined on Nov 2009 @ Worthing, England	#3

Originally Posted by zimon

This bug manifests also with HealthCheck program when using its reboot-tool.

technically the bug sits in the terminal command run within healthcheck

theres a thread on it all somewhere.

__________________
----------- Follow me on Twitter here
----------- My Photography Website and Blog is here
----------- Author of the N900 Health Check Application ----------- New Version in Extras Devel (Dec 2010 - 2.9.10)
----------- Are you on the N900 World Map? - http://pininthemap.com/maemo - masterpin: shotgun
----------- What apps do you want to see on the n900 or in MeeGo in the future? -

Quote & Reply |

« Previous Thread | Next Thread »

Forum Jump

All times are GMT. The time now is 00:29.

Active Topics

Is there a section to talk about Java ME? Apps, etc. (3)