Poll: How much would you be willing to pay for a Neo900 (complete device) with TI DM3730 1GHz/512M-RAM/1GB
Poll Options
How much would you be willing to pay for a Neo900 (complete device) with TI DM3730 1GHz/512M-RAM/1GB

Reply
Thread Tools
joerg_rw's Avatar
Posts: 2,222 | Thanked: 12,651 times | Joined on Mar 2010 @ SOL 3
#2391
Code:
From:	Ivaylo Dimitrov <ivo.XXXXXXXXXXXXXXX>
To:	neo900-devel@XXXXXXXXXX
Date:	2015-04-20 Mon 23:06
Hi,

I was able to boot to u-boot on onenand:

U-Boot# onenand erase

OneNAND erase: whole chip
OK
U-Boot# loadb
## Ready for binary (kermit) download to 0x80200000 at 115200 bps...

!!! x-load.bin.ift through kermit

U-Boot# onenand write 80200000 0 40000

OneNAND write: offset 0x0, size 0x40000
  262144 bytes written: OK
U-Boot# loadb
## Ready for binary (kermit) download to 0x80200000 at 115200 bps...

!!! u-boot.bin through kermit

onenand write 80200000 100000 80000

OneNAND write: offset 0x100000, size 0x80000
  524288 bytes written: OK
U-Boot# reset
resetting ...
U**60**

Texas Instruments X-Loader (OneNAND) 1.4.4ss modified for GTA04 (Apr 20 
2015 - )
Detected Samsung KCE00E00CA A506
OMAP36XX/37XX-GP ES2.1
Board detected: GTA04A7
SYSBOOT[5:0]: 0x10/16
GMPC Memory: 3
SDRC Memory: SAMSUNG MCP 512MB/bank
Loading u-boot.bin from onenand


U-Boot 2015.04-dirty (Apr 14 2015 - 23:58:05)

OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-200MHz, Max CPU Clock 1 Ghz
OMAP3 Beagle board + LPDDR/NAND
I2C:   ready
DRAM:  1 GiB
NAND:  Muxed OneNAND 512MB 1.8V 16-bit (0x50)
OneNAND version = 0x0232
Chip support all block unlock
Chip has 4KiB pagesize
Scanning device for bad blocks
OneNAND: 512 MiB
MMC:   OMAP SD/MMC: 0
Using default environment

Beagle xM Rev C
No EEPROM on expansion board
Die ID #606200029ff80000014f8e6f0601001c
Net:   usb_ether
Error: usb_ether address not set.

Hit any key to stop autoboot:  0
Card did not respond to voltage select!
Card did not respond to voltage select!
Booting from nand ...
Unknown command 'nand' - try 'help'
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Card did not respond to voltage select!
** Bad device mmc 0 **
U-Boot#
 

The Following 19 Users Say Thank You to joerg_rw For This Useful Post:
Posts: 15 | Thanked: 43 times | Joined on Feb 2015
#2392
Hi,
I know, it is quite late for a feature request and cannot expect such a thing to be included, but I'll post it anyway.

Would it be possible to include a 433Mhz receiver/transceiver combo in the Neo900? With this one would be able to control many garage doors, radio controlled power sockets etc. with the Ne900.

mith

Last edited by mithrandir; 2015-04-28 at 20:49. Reason: typo
 

The Following User Says Thank You to mithrandir For This Useful Post:
Posts: 162 | Thanked: 962 times | Joined on Jan 2014
#2393
Originally Posted by mithrandir View Post
Hi,
I know, it is quite late for a feature request and cannot expect such a thing to be included, but I'll post it anyway.

Would it be possible to include a 433Mhz receiver/transceiver combo in the Neo900? With this one would be able to control many garage doors, radio controlled power sockets etc. with the Ne900.

mith
If you got the sufficient knowledge, you can add by yourself via hackerbus. That's the beauty of this project.
 
nokiabot's Avatar
Posts: 1,974 | Thanked: 1,834 times | Joined on Mar 2013 @ india
#2394
Originally Posted by mithrandir View Post
Hi,
I know, it is quite late for a feature request and cannot expect such a thing to be included, but I'll post it anyway.

Would it be possible to include a 433Mhz receiver/transceiver combo in the Neo900? With this one would be able to control many garage doors, radio controlled power sockets etc. with the Ne900.

mith
not fesible i asked before you can use damm hackerbus to attach stuff
but you and i know intregated is so much better.
 
joerg_rw's Avatar
Posts: 2,222 | Thanked: 12,651 times | Joined on Mar 2010 @ SOL 3
#2395
fixed another bug in prestashop:
[2015-04-29 Wed 05:02:09] <DocScrutinizer05> http://wstaw.org/m/2015/04/29/plasma-desktoptw1950.png :-S prestashop is really a PITA - yet:
[2015-04-29 Wed 04:41:48] <DocScrutinizer05> HEHE my FF is german and guess WHAT
[2015-04-29 Wed 04:42:17] <wpwrak> dresses ?
[2015-04-29 Wed 04:42:26] <DocScrutinizer05> http://wstaw.org/m/2015/04/29/plasma-desktoptw1950.png
[2015-04-29 Wed 04:42:40] <wpwrak> hehe
[2015-04-29 Wed 04:43:15] <DocScrutinizer05> so now we already know WHAT happens (somewhat)
[2015-04-29 Wed 04:43:38] <DocScrutinizer05> now let's see if we find out WHY prestashop shows different content for Germans
[2015-04-29 Wed 04:44:35] <wpwrak> lemme try something ...
[2015-04-29 Wed 04:44:42] <DocScrutinizer05> here MUST be some option in prestashop to intentionally create language specific pages
[2015-04-29 Wed 04:44:49] <wpwrak> please reload
[2015-04-29 Wed 04:45:00] <DocScrutinizer05> AWESOME!!
[2015-04-29 Wed 04:45:08] <DocScrutinizer05> what did you do?
[2015-04-29 Wed 04:45:50] <DocScrutinizer05> I hope you didn't edit /srv/www/my.neo900/conf/config.in.php ;-)
[2015-04-29 Wed 04:45:55] <wpwrak> LOCALIZATION / Localization > Set language from browser: NO
[2015-04-29 Wed 04:46:06] <wpwrak> all cleanly in the admin interface
[edit] almost forgot: we got a nearly complete list of voucher codes for all our donors which we will complete and send out by email as soon as shop works decently. Many thanks to Werner for the incredible scripting and checking job done.



Secured 250 of the supposedly unobtainium Knowles speakers, just in case we might need a few. So don't worry about XPROT, there are spares




Last edited by joerg_rw; 2015-04-29 at 11:59.
 

The Following 19 Users Say Thank You to joerg_rw For This Useful Post:
Posts: 567 | Thanked: 2,965 times | Joined on Oct 2009
#2396
Ok so which hardware components are going to give us the biggest problem at this point?
 

The Following 4 Users Say Thank You to jonwil For This Useful Post:
joerg_rw's Avatar
Posts: 2,222 | Thanked: 12,651 times | Joined on Mar 2010 @ SOL 3
#2397
Originally Posted by jonwil View Post
Ok so which hardware components are going to give us the biggest problem at this point?
basically none, that's really great news
Most cumbersome for now: domesheet, but that's manageable
/j
 

The Following 13 Users Say Thank You to joerg_rw For This Useful Post:
Feathers McGraw's Avatar
Posts: 654 | Thanked: 2,368 times | Joined on Jul 2014 @ UK
#2398
Woah. Is it just me or did the predicted cost just jump up? I only noticed this because I've been keeping a close eye on neo900.org and noticed the updated FAQ and link to this:

http://neo900.org/estimate

EUR 990 for a NeoN kit, and an extra EUR 150 for a full Neo900 (that's EUR 1140 total, before VAT!).

Including VAT @ 20% in the UK, that's EUR 1368, just over £1000... I'm really struggling to be positive about this, not sure I'll be able to afford it.
 

The Following 12 Users Say Thank You to Feathers McGraw For This Useful Post:
Posts: 986 | Thanked: 1,526 times | Joined on Jul 2010
#2399
the reason why is made clear right on that page: inflation of euro compared to usd.
"Today's EUR 990 would be about EUR 770 at last year's value."

i was about to say that i could no longer afford it, until i realized that the price didnt change all that much for me in the US. {works out to 100$USD more than i expected, since i already paid some of it}
__________________
~ teleshoes ~
 

The Following 4 Users Say Thank You to wolke For This Useful Post:
endsormeans's Avatar
Posts: 3,139 | Thanked: 8,156 times | Joined on Feb 2013 @ From my Gabriola Island hermitage, near the Edge of the World
#2400
I wasn't going to say boo...but I sure am now.
@wolke ...I don't know how you came to the conclusion it is only a hundred bucks more....are you kidding me? really?
...and the euro-slide aside ...the entire globe took an economic hit from the oil almost flatlining. It wasn't just the Euro that got hurt.

Here it sits...the Canadian dollar is only 18 cents from parity with the US dollar...
here is exactly the sitch...the original ballpark estimate was 700 euros for a complete device. I was fine with that... I anticipated more even...and I was fine with that...
but 990euros+150euros = 1140 euros ...that isn't a hundred dollars more...that isn't a small or modest increase ...260 euros more and it's double the original estimate. and that 1140 euros is not final.


Before fees, duty, taxes etc...that 700 euros (for a complete device) = 780 usd = 944.65 cdn .
After calculating tax (which is + $133 cdn)
going from the original estimate of $1054~ cdn. (I'm NOT even counting duty or including shipping and handling)

to the present current revised estimate of (990euros + 150euros for the complete device) 1140 euros = $1269.29 usd = $1537.23 cdn (after tax calculating $184.47) its $1725~ cdn. (and yet again I'm NOT including duty, shipping and handling)
and that's saying that is the final set price tag of course...
that isn't just a hundred dollars more...in whatever denomination...
that is going from the original estimate (in my country) of a grand to $275 dollars shy of DOUBLE the original estimate...

I've already put down over $600 cdn and I'm still $1100 bucks away?
and then there is STILL on top of that duty, shipping, handling, and insurance (I would imagine). I imagine it will be a joy to see that end figure.

The new estimation is a punch-to-the-gut number ...
it is becoming hard calling it anything different..

I do get the math...and understand the sitch (the euro slide, the unforeseen costs, etc..) ...I get it.
and I do want to see the guys getting paid decently, costs covered, the whole shmozzel...

I still intend on getting a device..
I still support the project...
I still believe in the project...
I'm not griping or complaining...
But if I'm handing over a couple hundred bucks shy of 2 grand (and I won't be surprised it makes that figure in the end)...
I think no one would deny me the allowance to say ..something...
guys..that number ... $1725~ cdn.
I can only speak for myself when I say …
flat-out that number smarts..really smarts.
__________________
Lurker since 2007, Member since 2013, Certifiable since 1972

Owner of :
1-n770 (in retirement), 3-n800's / 3-n810's (still in daily use), 5-n900's ((3 are flawless, 1 loose usb ( parts), 1 has no telephony (parts))
3-nexus 5's : 1 w/ Floko Pie 9.1 (running beautifully) waiting for Stable Droid 10 rom, 1 w/ ̶Ubuntu Touch, 1 with Maru OS (intend maemo leste when ready)

1/2 - neo900 pre- "purchased" in 2013. N̶o̶w̶ ̶A̶w̶a̶i̶t̶i̶n̶g̶ ̶r̶e̶f̶u̶n̶d̶ ̶p̶r̶o̶c̶e̶s̶s̶ ̶l̶a̶s̶t̶ ̶f̶e̶w̶ ̶y̶e̶a̶r̶s̶ - neo900 start up declared officially dead -
Lost invested funds.


PIMP MY N8X0 (Idiot's Guide and a video walkthrough)http://talk.maemo.org/showthread.php?t=94294
THE LOST GRONMAYER CATALOGShttp://talk.maemo.org/showthread.php...ight=gronmayer
N8X0 VIDEO ENCODING THE EASY WAYhttp://talk.maemo.org/showthread.php...ght=mediacoder
242gb ON N800http://talk.maemo.org/showthread.php?t=90634
THE PAIN-FREE MAEMO DEVELOPMENT LIVE DISTRO-ISO FOR THE NOOB TO THE PROhttp://talk.maemo.org/showthread.php?t=95567
AFFORDABLE MASS PRODUCTION FOR MAEMO PARTShttp://talk.maemo.org/showthread.php?t=93325

Meateo balloons now available @ Dave999's Meateo Emporium

Last edited by endsormeans; 2015-05-05 at 06:30.
 

The Following 13 Users Say Thank You to endsormeans For This Useful Post:
Reply

Tags
neo900, thank you!

Thread Tools

 
Forum Jump


All times are GMT. The time now is 10:09.