Active Topics

 


Reply
Thread Tools
Posts: 189 | Thanked: 143 times | Joined on Nov 2009
#1
Hi everybody,

as there is no spare battery available for the JollaC outside of India.

I wrote a short tutorial on how to make the UMI X2 battery JollaC compatible. A big thanks to TJC user Giacomo Di Giacomo who gave the tip in the spare battery thread that it fits the JollaC.

Warning: Your warranty will be voided. And you could destroy your phone with this guide. I am not responsible for any damaged phone. And don't point a finger at me if you failed to solder everything properly.

Please only do this DIY if you know what you are doing. If you never used a solder iron before please DO NOT DO IT!!! The battery could explode if it gets too hot.


What you need:
- UMI X2 battery (http://www.ebay.de/itm/Akku-fur-UMI-...oAAOSw9N1Vjsqg)
- soldering iron (best with a thin tip)
- tin-solder
- scissors
- pencil
- heat shrink tube or any other isolating material which fits around the battery
- cable stripper
- thin cables (black, red, yellow)
- adhesive copper foil (https://www.amazon.de/Kupfer-Heizung...dp/B017LB9AJW/) or any type of copper, brass
- a vice or something to hold your battery
- multimeter
- A table with good light
- patience

Let's begin
First of all prepare all the stuff you need. It's annoying if you need to search for things during the work.



To make placing of the copper foil easier, we mark the positions of the contacts with a pencil using the old battery.



Extend the markings to the top of the battery.


Skin the cables and prepare them with tin-solder. Also cut the skin ends to a suitable length.


Put your battery in a vice, but don't use too much force!


Prepare your solder iron with a thin tip and set the temperature to 400°C.



Prepare the battery with a bit of tin-solder (makes it easier and faster when you attach the cables).


Attach the cables (black -, yellow charging, red +).


Cut the copper foil that it fits your markings. And 3 different lengths, make sure that the longest copper strip is outside facing.



Solder the cables to it, use your old battery to check if your contacts are in the right order (minus is the outside facing contact). Make sure that the cables don't cross each other, otherwise you will get a bulge in your backcover.


Check the contacts with your old battery and a multimeter. If the multimeter shows approx 3,8V between + and - aswell as + and yellow everything should be alright.

Place the battery in your phone to check if everything fits or if you need to adjust something.



If everything fits and you are sure that you have the cabling correct. Try to power on the phone.


If that worked you can apply the heat shrink. Make sure that you isolate the original contacts of the battery.




Finally check if your phone charges.


If you did a good job and used thin cables the cover does still fit and does not have a bad bulge. Mine has a small one not really noticeable (at least better than my thickened battery ).



Screenshots of CSD Tool after the fix (phone was charging that's why the discharge test fails):




You can check these things via CLI too:

Last edited by MaemoUser; 2017-01-15 at 13:50.
 

The Following 22 Users Say Thank You to MaemoUser For This Useful Post:
Community Council | Posts: 4,920 | Thanked: 12,867 times | Joined on May 2012 @ Southerrn Finland
#2
Very detailed tutorial, lovely!
 

The Following 3 Users Say Thank You to juiceme For This Useful Post:
Posts: 539 | Thanked: 518 times | Joined on May 2010 @ nanaurbusiness
#3
Giacomo posted a picture at together.jolla

Nice work I'd say.
__________________

N900 ~ $ make me a sandwich
-bash: no, make it yourself
N900 ~ $ sudo make me a sandwich
-bash: ok then...
 

The Following 4 Users Say Thank You to J4ZZ For This Useful Post:
Posts: 189 | Thanked: 143 times | Joined on Nov 2009
#4
Yeah, I know (that's why I linked the thread and mentioned him ). But some users wanted a more detailed report on how to do that. Not only a picture of the result .
 

The Following 3 Users Say Thank You to MaemoUser For This Useful Post:
Posts: 189 | Thanked: 143 times | Joined on Nov 2009
#5
Added screenshots of CSD-Tool.

Last edited by MaemoUser; 2017-01-15 at 13:33.
 

The Following 4 Users Say Thank You to MaemoUser For This Useful Post:
Posts: 578 | Thanked: 994 times | Joined on Dec 2012
#6
I think CSD tests give nothing more than: it works. More interesting would be voltage drop on this tiny wires under heavy load or charging ( > 1 A), especially looking at Giacomo's mod.
 

The Following 2 Users Say Thank You to elros34 For This Useful Post:
Posts: 189 | Thanked: 143 times | Joined on Nov 2009
#7
You can draw more current than you would expect through those cables.
https://learn.adafruit.com/wires-and...ns/wire-guages

And did you see the contacts which connect to the battery? Much smaller than any of the cables used by me or Giacomo.

Last edited by MaemoUser; 2017-01-15 at 15:26.
 

The Following 2 Users Say Thank You to MaemoUser For This Useful Post:
Posts: 189 | Thanked: 143 times | Joined on Nov 2009
#8
Started a short load test with stresser.

stress-ng --cpu 4 --timeout 60


Voltage drops not more than with original battery. (4082 mV to 3906mV)

Last edited by MaemoUser; 2017-01-15 at 15:30.
 

The Following 4 Users Say Thank You to MaemoUser For This Useful Post:
TMavica's Avatar
Posts: 2,021 | Thanked: 1,060 times | Joined on Apr 2010 @ Hong Kong
#9
There is spare battery available in India, but it wont ship oversea
__________________
The Glorious Lady T.Mavica
Twitter https://twitter.com/TMavica
 

The Following User Says Thank You to TMavica For This Useful Post:
Posts: 189 | Thanked: 143 times | Joined on Nov 2009
#10
That's what I wrote in my first sentence .
 

The Following 6 Users Say Thank You to MaemoUser For This Useful Post:
Reply

Tags
battery, diy project, jollac

Thread Tools

 
Forum Jump


All times are GMT. The time now is 02:28.