drucula is offline drucula
06-25-2011 , 03:00 PM
Posts: 34 | Thanked: 44 times | Joined on Sep 2010 @ Israel
#1
Lately I've been experiencing some problems with my wifi connection.
My phone is unable to connect to any APs available around most of the time. Whenever it connects to an AP, it immediately disconnects within 5 minutes.
The weird thing is that I experience no problems with wifi in meego and in nitdroid.
I believe that a reflash would solve the problem but I prefer to overcome the problem without it.
Honestly, I have no idea on how to approach to this problem since I'm no linux expert.
Anyway, here are some logs if they help:
dmesg:
Code:
[46282.278198] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[46282.293853] wl1251: firmware booted (Rev 4.0.4.3.7)
[46282.497039] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[46283.262786] wl1251: down
[46287.856353] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[46287.856689] wl1251: firmware booted (Rev 4.0.4.3.7)
[46287.885925] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[46288.723785] wlan0: authenticate with AP 00:0e:2e:c3:86:40
[46288.726959] wlan0: authenticated
[46288.727020] wlan0: associate with AP 00:0e:2e:c3:86:40
[46288.764801] wlan0: RX AssocResp from 00:0e:2e:c3:86:40 (capab=0x411 status=0 aid=2)
[46288.764862] wlan0: associated
[46288.810302] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[46289.500274] wlan0: disassociated
[46290.478759] wlan0: deauthenticating by local choice (reason=14)
[46290.478820] wlan0: deauthenticating by local choice (reason=3)
[46290.497741] wlan0: associate with AP 00:00:00:00:00:00
[46290.692077] wlan0: associate with AP 00:00:00:00:00:00
[46290.887390] wlan0: associate with AP 00:00:00:00:00:00
[46291.082702] wlan0: association with AP 00:00:00:00:00:00 timed out
[46292.379974] wl1251: down
[46298.739196] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[46298.739532] wl1251: firmware booted (Rev 4.0.4.3.7)
[46298.768035] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[46299.661621] wl1251: down
[46300.504882] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[46300.520446] wl1251: firmware booted (Rev 4.0.4.3.7)
[46300.638153] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[46307.005218] wl1251: down
[46314.262512] slide (GPIO 71) is now open
[46315.200012] slide (GPIO 71) is now closed
[46336.950103] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[46336.965698] wl1251: firmware booted (Rev 4.0.4.3.7)
[46337.099121] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[46338.247528] wl1251: down
[46339.043945] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[46339.044342] wl1251: firmware booted (Rev 4.0.4.3.7)
[46339.177276] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[46346.067718] wl1251: down
[46347.161102] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[46347.161468] wl1251: firmware booted (Rev 4.0.4.3.7)
[46347.192840] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[46347.941284] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 1
[46348.129760] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 2
[46348.325042] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 3
[46348.520355] wlan0: direct probe to AP 00:21:63:ed:9f:76 timed out
[46348.606628] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 1
[46348.801605] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 2
[46348.996917] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 3
[46349.192260] wlan0: direct probe to AP 00:21:63:ed:9f:76 timed out
[46349.919891] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 1
[46350.114105] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 2
[46350.309417] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 3
[46350.504852] wlan0: direct probe to AP 00:21:63:ed:9f:76 timed out
[46351.768432] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 1
[46351.957855] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 2
[46352.153228] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 3
[46352.348480] wlan0: direct probe to AP 00:21:63:ed:9f:76 timed out
[46353.672027] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 1
[46353.864135] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 2
[46354.059356] wlan0: direct probe to AP 00:21:63:ed:9f:76 try 3
[46354.254730] wlan0: direct probe to AP 00:21:63:ed:9f:76 timed out
[46354.349029] wl1251: down
[46355.535980] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[46355.551513] wl1251: firmware booted (Rev 4.0.4.3.7)
[46355.692596] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[46356.551849] wl1251: down
[46358.817321] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[46358.817657] wl1251: firmware booted (Rev 4.0.4.3.7)
[46358.865051] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[46360.325286] wlan0: authenticate with AP 00:0e:2e:c3:86:40
[46360.328674] wlan0: authenticated
[46360.328735] wlan0: associate with AP 00:0e:2e:c3:86:40
[46360.344635] wlan0: RX AssocResp from 00:0e:2e:c3:86:40 (capab=0x411 status=0 aid=1)
[46360.344696] wlan0: associated
[46360.395751] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[46371.363983] wlan0: no IPv6 routers present
[46393.543701] slide (GPIO 71) is now open
[46409.943969] wlan0: disassociated
[46409.968780] wlan0: deauthenticated
[46410.902069] wlan0: deauthenticating by local choice (reason=14)
[46410.902130] wlan0: deauthenticating by local choice (reason=3)
[46410.965545] wlan0: direct probe to AP 00:00:00:00:00:00 try 1
[46411.160919] wlan0: direct probe to AP 00:00:00:00:00:00 try 2
[46411.356140] wlan0: direct probe to AP 00:00:00:00:00:00 try 3
[46411.551422] wlan0: direct probe to AP 00:00:00:00:00:00 timed out
[46412.512725] wl1251: down
[46424.684356] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[46424.700134] wl1251: firmware booted (Rev 4.0.4.3.7)
[46424.728393] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[46425.645965] wl1251: down
[46430.786041] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[46430.801635] wl1251: firmware booted (Rev 4.0.4.3.7)
[46430.935241] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[46438.114776] wl1251: down
[46458.301544] wl1251: 151 tx blocks at 0x3b788, 35 rx blocks at 0x3a780
[46458.317291] wl1251: firmware booted (Rev 4.0.4.3.7)
[46458.435211] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[46459.231445] wl1251: down
ifconfig wlan0:
Code:
wlan0     Link encap:Ethernet  HWaddr 0C:DD:EF:4A:5F:CB  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:1747 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1644 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:547259 (534.4 KiB)  TX bytes:312716 (305.3 KiB)
iwconfig wlan0:
Code:
wlan0     IEEE 802.11bg  ESSID:""  
          Mode:Managed  Frequency:2.442 GHz  Access Point: Not-Associated   
          Tx-Power=10 dBm   
          Retry min limit:7   RTS thr:off   Fragment thr=2352 B   
          Encryption key:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0
So... what should be my next move?
 
drucula is offline drucula
06-27-2011 , 01:15 PM
Posts: 34 | Thanked: 44 times | Joined on Sep 2010 @ Israel
#2
bump?
10 chars
 
jbd is offline jbd
08-21-2012 , 04:45 AM
Posts: 15 | Thanked: 6 times | Joined on Feb 2011
#3
Hi Drucula,

Did you find any fix to your problem?

I have the same dmesg messages, except after "ADDRCONF(NETDEV_UP): wlan0: link is not ready" it doesn't authenticate to any network, just times out.

My iwconfig wlan0 has Tx-Power set to 20.

Thanks,

jb
 
sixwheeledbeast is offline sixwheeledbeast
08-21-2012 , 07:49 AM
Posts: 1,370 | Thanked: 1,897 times | Joined on Apr 2010 @ St. Helens, England
#4
@jbd
I had the same issue

http://talk.maemo.org/showthread.php?t=85701
__________________
The stable-beast currently runs...
21.2011.38-1Smaemo6 (CSSU Stable)
2.6.28.10power50 (125-600Mhz SR VDD1&2)
__________________________________________________
sixwheeledbeast's wiki
- mcallerx - tenminutecore - FlopSwap -
Testing Squad Subscriber
__________________________________________________
Before posting in a thread please try this.
Before starting a new thread please try this.
 
Reply

« Previous Thread | Next Thread »
Thread Tools Search this Thread
Search this Thread:

Advanced Search

 
Forum Jump


All times are GMT -4. The time now is 09:02 PM.

Contact Us - Home - Archive - Top