View Full Version : Kick stand Lever broken..Pics attached..Suggestions Please
So the kick stand spring / lever broke loose autoMagically today. The n900 is less than 2 months old. I feel that the plastic rivets are too flimsy to hold this steel lever in place.
What could be the best method to fix it back? I am thinking along the lines of a epoxy glue.
breakd0wn
2010-06-27, 07:54
Just order a new battery cover?
buy a new backside or go into a store and switch it from a demo device ;) two suggestions...one good and one bad :)
Thanks for the suggestions :) Appreciated!
Here's the results of the epoxy fix :P
I think $20 for a new cover is a bit too rich for my wallet.. since the design of the cover is a bit shoddy and the engineer in me would not allow me to repeat the same mistake twice :)
how did the glue fix it, pictures still look like it's broken =(
how did the glue fix it, pictures still look like it's broken =(
The epoxy is a very strong glue and holds things strongly, once it sets. It's difficult to convince though with the picture :)
ahh you know i always find it funny seeing photos of n900s posted its like i almost think the only camera anyone owns is indeed the n900 its self !
i remember having to take a photo of mine and i was stumped for 5 minutes with where i'd find another camera device to do it =)
feighery
2010-06-29, 09:15
Buy a glue gun in maplins and hot glue it on, might be a cleaner job.
ahh you know i always find it funny seeing photos of n900s posted its like i almost think the only camera anyone owns is indeed the n900 its self !
i remember having to take a photo of mine and i was stumped for 5 minutes with where i'd find another camera device to do it =)
I completely understand what you mean. :) Infact these pics are using my N95-1. Yup I still have it, though using it w/o a simcard, mainly as a bluetooth enabled camera.
Thanks for the suggestion. Just realised, I did have a glue gun, but unfortunately didn't have glue sticks that go with it.
Wikiwide
2010-06-29, 10:07
ahh you know i always find it funny seeing photos of n900s posted its like i almost think the only camera anyone owns is indeed the n900 its self !
i remember having to take a photo of mine and i was stumped for 5 minutes with where i'd find another camera device to do it =)
Take a mirror...
N900 may work without back cover (with back cover off). Photograph attached.
pantera1989
2010-06-29, 10:40
Look on the bright side. Now your photos won't be affected by the camera flash reflecting on the chrome.
nick.read
2010-07-13, 04:25
Bah! Same thing happened to me today. The "L" shaped clip fell off. I have both epoxy and a glue gun handy, so now I just have to try and decide which to use. Don't know if I'll do the straight clip in-place, rip it off and put glue underneath it, or just wait until it falls off naturally :)
get a replacement off ebay.
http://shop.ebay.co.uk/i.html?_nkw=n900+fascia&_sacat=0&_odkw=n900+keypad&_osacat=0&bkBtn=&_trksid=p3286.m270.l1313
cheap.
lucas777
2010-07-13, 04:58
I always had a fear about this breaking on mine, they seem pretty flimsy gl with fixing it mate
maartenmk
2010-07-13, 05:37
Bah! Same thing happened to me today. The "L" shaped clip fell off. I have both epoxy and a glue gun handy, so now I just have to try and decide which to use. Don't know if I'll do the straight clip in-place, rip it off and put glue underneath it, or just wait until it falls off naturally :)
If your glue gun doesn't have much better glue than the ones I know, use the epoxy. And don't forget to de-grease first!
The glue gun may still be handy to hold it in place while the epoxy hardens though.
hassan_badredin
2010-07-13, 18:35
I had mine fall off just today!!!!
i used *that, heated on the kitchen **stove and applied ***there :D
worked like a charm, i think even better than glue, though i wish i had both..
vBulletin® v3.8.8, Copyright ©2000-2024, vBulletin Solutions, Inc.