Originally Posted by rog (Post 980463)

A BIG Thank You FRuMMaGe for the great app and of course to lxp for his hard work to make this happen (wish I can donate but I am broke at the mom. I promise I will when back on my feet).
Few thinks I encounter when playing with it
1. in decrypt under dictionaries I see u have an all.lst & sky.txt something I don’t is just me or somebody else have same problem (or maybe I fgot to load something during installation)
2. after scanning for networks (wep & wpa), happen only with some of them even I have a strong signal when click on it nothing happen (ex. No netw. Info in the white window and if I click on start packet capture nothing happens) again is just me or someone else have the same problem.
3. I read somewhere (can’t remember where) you mentioned for wpa you can force a mac to disconnect, for a quicker handshake, how do you do it, or will be great if you can add a button with a window where we can enter the desire mac on the future release. (correct me if I am wrong pls. but as far as I know no 2 mac can be on the same netw. At the same time)
Also a few small thinks I can see the key in the small window but I can not copy & paste from it (you have to open the .txt file to do so or remember the key) so will be much easy if this can be possible on a future release. After I installed another app (was a game) faircrack did not worked, I had to reboot then everything was fine. I read some people ha d problems after using the app they could not get the wifi working because they forgot to switch back to manager mode, I have installed an ap wifi switcher if you click on it will start stop your wifi hopefully this will solve the problem much easier for some. The rest as far as played with it worked great for me on some networks more than others (of course with the netw. Owners permission) more or less wep got decrypted in around 8 min. from start to finish if the signal was over 20%, on some routers did not work at all (I think b cos the settings on it,), about the wpa I only tried ones on my network could not get the handshake at the start but that was b cos the settings on the router ex. If you reserve the ip address even if you disconnect and reconnect will not work I believe to get a handshake the settings on d device has to be set to obtain an automatic ip address from the router after I did that I got a handshake, left the n900 over night to work on d key with no success after 11:45hrs (the key is 26 digit long alphanumeric), again thanks for the great app., will let you know if I will run into something else.

Originally Posted by lucas777 (Post 982247)

Cant read a word of this, hurting my eyes

Originally Posted by garen (Post 987064)

Every time i even open the app, my wifi connections stop working and i need to reboot for me to be able to use them again. How can i fix it?

Originally Posted by jonarmani (Post 987104)

Do you disable the drivers in the app when you're done? WiFi won't work in a normal fashion while you have the injection drivers loaded.

Originally Posted by fabfour (Post 987377)

press the monitor tab and press the button disable under packet injection easy i guess

Originally Posted by TobiasReaper (Post 994504)

First, a big ty for FRuMMaGe for making this app ^^

If anyone has the link for WEPCrackGUI, please do share.

Originally Posted by TobiasReaper (Post 994537)

and authenticate?

Originally Posted by codecxbox (Post 994653)

You really do not need these 2 steps, if the AP you are attacking has a lot of wifi traffic, like if other clients are connected to the AP at the same time and those clients are active, like downloading or torrenting. But if these clients are idle or the AP doesnt have any clients attached, it would take a long time to capture enough packets for Aircrack to decrypt.
Its like if you attack a AP in a shopping mall, you wouldnt have to inject and authenticize. But if you were in a desert attacking a AP without any clients, you would have to inject. Think about like your N900 doing 2 jobs at the same time, a normal client and the attacker.

Originally Posted by Swirnoff (Post 998754)

How many IV's does it show you have collected before closing?

Originally Posted by SkyKnight (Post 998791)

around 1lakh of em...

Originally Posted by SkyKnight (Post 998752)

I successfully completed the packet injection phase to around 1lakh plus ARPs and when i click the decrypt tab, the window pops up showing info of captured packets and then just before it starts decryption it exits...

Any help ppl???

I have packet capture, authenticate and packet injection windows running when i do this...

Should any of em be closed for decryption to work??

Originally Posted by Brian_7 (Post 974123)

Hi, when will we have the new version that solves the error with de networks that have a space in their names?

Originally Posted by slewis1972 (Post 1001321)

Does this work with kernel power 47?

Originally Posted by arnoldux (Post 1001332)

i dont think it works with kernel 47 cuz its not modified witht he patches

but still, anyone help me on my problem? i even reinstalled faircrack and lxp inyection drivers and nothing :S never authenticates, it keeps saying sending authentication request (open system)

cheers

Originally Posted by arnoldux (Post 1001376)

i found my problem, the injection drivers wont load

http://imageshack.us/photo/my-images...enshot03k.png/

and i dont know what to do :(

thanks in advance

Originally Posted by arnoldux (Post 1001376)

i found my problem, the injection drivers wont load

http://imageshack.us/photo/my-images...enshot03k.png/

and i dont know what to do :(

thanks in advance

Originally Posted by avidscavenger (Post 1000991)

Quite simple. Change the file ~/MyDocs/FAS/readAP.sh to: