Re: [Announce] Cleven - an aircrack gui
 

Did you remember to disable monitor mode and injection and also if you have the same mac address as your host you need to change it.

Re: [Announce] Cleven - an aircrack gui
 

Hello again,

This time, not playing with my own router, but testing a friend's one, I seem to have the same problem as Miroslav, but let me confirm it is WEP protected *not* wpa
I also know it is active since there is a PS3 and a laptop connected to it, also aware it is MAC-filtered. I am using either the PS3 or the laptop's mac using MACChanger, but the data collection is incredibly slow... Removing the Mac filter, as well as testing in my network, WEP protection usually reaches 50k in a few minutes, but I don't understand what I seem to be doing wrong here...

*Edit: I am always doing this using N900's Tablet Mode, but I don't think it should change anything... (for power consumption issues)

Re: [Announce] Cleven - an aircrack gui
 

Obviously, you're collecting without proper injection. so, 1000 IV's You got in hour is quite good. You need to use authorised (properly) MAC, and inject.

Please, all of this belongs to aicrack-ng forum, not Cleven GUI thread. This was last "generic" aircrack-ng question I'm answering here. This thread is *not* appropriate for such talks.

Re: [Announce] Cleven - an aircrack gui
 

all i did was i opened cleven. enable monitor mode. set injection drivers. den set mac address. then tapped outside. scand for available networks and authenticated the desired network. xterminal opened. data collected upto 52k. den decrypted successfully. showed keys. but cannot connect with that key. :(

Re: [Announce] Cleven - an aircrack gui
 

done sudo apt-get install kernel-power from extras-devel
after installation
uname -r gives 2.6.28-omap1

:s

cleven says no compatable kernel to load injection drivers or soemthing like that !!!

Re: [Announce] Cleven - an aircrack gui
 

Hey Saturn, any findings/progress about why "all common" doesn't work for sample network names I've send You? Also, do you plan to enable broadcast deauth for WEP cracking (not only WPA) as it helps to create ARP package for injection? not demanding anything (by any means), but it's a shame that Cleven isn't still stand-alone equivalent for fAircrack (while Cleve is superior in many areas, or is supposed to be [''all common'']).

/Estel

Re: [Announce] Cleven - an aircrack gui
 

Hello everyone..i m new here i just tried cleven but had a problem..i read the guide on page 15 and tried it but the problem is that when i try to hack a WEP i collect the minimum data and den wen i go to the decrypt window and press WEP i dont get any AP there its blank..can someone plzz help me out with dis??rest everything is ok..i m using power kernel 48 and its f99 but i cant see any AP in WEP SO PLZZ HELP??will be waitin for a reply thank you..

Re: [Announce] Cleven - an aircrack gui
 

[QUOTE=sansar95;1064267]I was sucessful in capturing some .cap file but donot know hat to do next from where to get the dicitonary file pls help

thanks in advance[/QUOTE

I have the same problem... I captured some wpa .cap but can't decrypt it, cause there is no dictionary, and pressing decrypt button doesn't do anything. Please, anybody help
Thanks in advance

Re: [Announce] Cleven - an aircrack gui
 

Hi,

FYI, mikemorrison has sent me a couple of correction for the file manipulations cleven is doing.

Next release will include those of course.

Please remember to thank him if you see him around :)

Re: [Announce] Cleven - an aircrack gui
 

I have never ever been able to crack WEP ad-hoc networks. Ever. It always show “Waiting for beacon frame” and then “No such BSSID available”. However, it works fine with WEP infrastructure networks. I've been through different versions of Cleven (and kernel) but it never worked for me. I don't know if it's an issue of Cleven or aircrack-ng. Apparently somehow aircrack-ng/Cleven didn't get the right BSSID (or at least it's what google tells me).

It's not that my installation is broken. I just did a reflash some days ago and reinstall the latest version.

Anyone succesfully cracked a WEP ad-hoc network?