[Announce] kernel-power stable v49 in Extras-Testing - Page 140 - maemo.org

ade | # 1391 | 2011-08-29, 20:22 | Report

Originally Posted by demiurgo0 View Post

how I can regain the kernel V47?

kernel-48 battery discharge so fast I

Are you sure it is not just a change in the way the battery power is measured (BME instead of BQ27200 etc)? In kernel-48, not all methods are enabled by default (see release notes).

The Following 2 Users Say Thank You to ade For This Useful Post:
don_falcone, Estel

demiurgo0 | # 1392 | 2011-08-29, 21:30 | Report

now with the kernel 48, the battery lasts less

as I set it up to last as the kernel 47?

you can help me?

ade | # 1393 | 2011-08-29, 22:03 | Report

Originally Posted by demiurgo0 View Post

now with the kernel 48, the battery lasts less

as I set it up to last as the kernel 47?

you can help me?

If you are so convinced it is the power kernel version fault...

The command should be something like:

Code:

sudo gainroot
apt-get --reinstall install kernel-power=2.6.28-10power47 kernel-power-modules=2.6.28-10power47 kernel-power-flasher=2.6.28-10power47

I didn't test it, so for your own risk!

The Following User Says Thank You to ade For This Useful Post:
n70shan

pali | # 1394 | 2011-08-29, 22:27 | Report

Sorry for log delay... Now I'm have some school obligations, so I do not have time for this thread. Now I do not read responces... If something urgent which cannot wait contact me...

I know, that it is not possible to use bq module in v48. Patch which disabled autoloading (in board code) also disable registring board info. So solution is disable autoloading by blacklist. Now it is fixed on git (will be released in v49). So v48 cant use bq module (who want must downgrade to v47 or upgrade from git)!

Next problem is with maemo.org package interface again :-(
settings package is Ok, new version I can promote. But flasher, modules, bootimg, debug, source, ... again interface does not see.

I used original maemo stock kernel tarball (I checked md5sum too, see repository.maemo.org page) and problem is still here...

So maybe we will not see new version of kernel-power in extras anymore :-( If somebody wants and has time, can try to find problem or contact X-Fade. I'm very unhappy that after 3 months I cannot promote packages to extras-testing...

The Following 8 Users Say Thank You to pali For This Useful Post:
don_falcone, drangina, Estel, kevloral, reinob, Trestry, woody14619, zimon

colin.stephane | # 1395 | 2011-08-29, 22:41 | Report

Originally Posted by pali View Post

Sorry for log delay... Now I'm have some school obligations, so I do not have time for this thread. Now I do not read responces... If something urgent which cannot wait contact me...

I know, that it is not possible to use bq module in v48. Patch which disabled autoloading (in board code) also disable registring board info. So solution is disable autoloading by blacklist. Now it is fixed on git (will be released in v49). So v48 cant use bq module (who want must downgrade to v47 or upgrade from git)!

Next problem is with maemo.org package interface again :-(
settings package is Ok, new version I can promote. But flasher, modules, bootimg, debug, source, ... again interface does not see.

I used original maemo stock kernel tarball (I checked md5sum too, see repository.maemo.org page) and problem is still here...

So maybe we will not see new version of kernel-power in extras anymore :-( If somebody wants and has time, can try to find problem or contact X-Fade. I'm very unhappy that after 3 months I cannot promote packages to extras-testing...

Hi pali,

On my side, I'm currently applying atop kernel patches to the v48.

I finally learned how to apply patches to the current kernel-power tree with quilt, and actually the compilation run ...

I use scratchbox on my side, and since my recent work on the kernel-power, I have already pushed many others packages on testing-devel.

I just don't understand what problems you have pushing new packages of your devel packages ...

A++

The Following User Says Thank You to colin.stephane For This Useful Post:
reinob

n70shan | # 1396 | 2011-08-29, 23:29 | Report

help!! my n900 is only stable up to 800mhz above that it reboots or gets dead . wht to do now? i also wna use it at 1000 mhz

Hurrian | # 1397 | 2011-08-29, 23:46 | Report

Originally Posted by n70shan View Post

help!! my n900 is only stable up to 800mhz above that it reboots or gets dead . wht to do now? i also wna use it at 1000 mhz

Increase voltage. Correct your spelling. Read the overclock thread.

colin.stephane | # 1398 | 2011-08-29, 23:52 | Report

Well,

I have successfully applied Atop kernel patches across v48.

Pali, is there a way I can push my packages into extra-devel ?

A++

n70shan | # 1399 | 2011-08-30, 01:10 | Report

Originally Posted by Hurrian View Post

Increase voltage. Correct your spelling. Read the overclock thread.

its for titans kernel. and kernel-config command not workinng in kp v48.

Hurrian | # 1400 | 2011-08-30, 02:08 | Report

Originally Posted by n70shan View Post

its for titans kernel. and kernel-config command not workinng in kp v48.

:facepalm:
This is a continuation of titan's kernel.
And BTW:

Code:

BusyBox v1.19.0 (Debian 1.19.0power3) built-in shell (ash)
Enter 'help' for a list of built-in commands.

~ $ uname -a
Linux sumomo 2.6.28.10-power48 #1 PREEMPT Mon Aug 22 15:09:51 EEST 2011 armv7l GNU/Linux
~ $ sudo kernel-config show
current kernel configuration:
current frequency: 600
supported frequencies: 125 250 500 550 600 700 750 805 850 900 950 1000 1100 1150
min. frequency: 250
max. frequency: 600
avoid frequencies: 125 550 700 805 850 900 950 1000 1100 1150
active frequencies: 0:20,90 250:30,180 500:33,360 600:39,430
SmartReflex VDD1=1 VDD2=1
governor ondemand: ignore nice load= 1, up threshold= 75, sampling rate= 150000, powersave bias= 0
~ $

How about you reflash your device, eMMC and rootfs then come back?