PR 1.3 for N950? - Page 11 - maemo.org

marmistrz | # 101 | 2012-11-15, 17:29 | Report

Could anyone upload the leaked PR1.3, in a non-torrent way, as I can't really download from torrents...? Thanks

caco3 | # 102 | 2012-11-15, 18:55 | Report

Why can you not download the torrent?

Cou can download it from my Diskstation if needed, how ever I cant promis it is fast

http://home.ruinelli.ch:5080/N950_PR1.3/

The Following 4 Users Say Thank You to caco3 For This Useful Post:
marmistrz, peterleinchen, sjgadsby, Wikiwide

marmistrz | # 103 | 2012-11-16, 14:05 | Report

Originally Posted by caco3 View Post

Why can you not download the torrent?

Cou can download it from my Diskstation if needed, how ever I cant promis it is fast

http://home.ruinelli.ch:5080/N950_PR1.3/

In the school network I wanted to download it in it's prohibited to use torrents. If you do so, you can't use it anymore.
The speed is acceptable, it has the resumable download option. Thanks very much!

The Following User Says Thank You to marmistrz For This Useful Post:
Wikiwide

antonioaraujob | # 104 | 2013-01-12, 01:51 | Report

Dear friends,
I have a problem with my N950. Yesterday the phone had a strange behaviour; the sent sms did not appear, the notes could not be showed and the file system was mounted in read only mode. After this I decided to flash the device again following the steps in: http://harmattan-dev.nokia.com/release/N950-39-5/. I say again because I did the flash process a couple of months ago.

The output of the process is the following:

Code:

Check first that device is powered OFF and then connect USB cable.

First erasing eMMC
Then flashing image and eMMC
Flashing started at 13:11:13

flasher 3.12.1 (Oct  5 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

Suitable USB interface (bootloader/phonet) not found, waiting...
USB device found at bus 002, device address 024.
Device identifier: xxxx (SN: N/A)
Found device RM-680, hardware revision 1124
NOLO version 2.3.6
Version of 'sw-release': DFL61_HARMATTAN_3.2012.02-6_PR_RM680
Sending ape-algo image (7032 kB)...
100% (7032 of 7032 kB, avg. 22114 kB/s)
Suitable USB interface (phonet) not found, waiting...
USB device found at bus 002, device address 025.
Device identifier: xxxxx (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.6.3
Found product RM-680 rev. 1124
Server implements softupd protocol version 1.8

Battery level 80 %, continuing.
Erasing, this may take a while.
Erase done.
Image SW version DFL61_HARMATTAN_2.2011.39-5_PR_RM680
Image moslo not present
Image tar skipped
Image config skipped

Battery level 85 %, continuing.

    image        [state    progress         transfer     flash speed]
---------------------------------------------------------------------
[_] cert-sw      [init         0 %       0 /       0 kB      NA     ]
[ ] cmt-2nd      [pending      0 %       0 /       0 kB      NA     ]
[ ] cmt-algo     [pending      0 %       0 /       0 kB      NA     ]
[ ] cmt-mcusw    [pending      0 %       0 /       0 kB      NA     ]
[ ] xloader      [pending      0 %       0 /       0 kB      NA     ]
[ ] secondary    [pending      0 %       0 /       0 kB      NA     ]
[ ] kernel       [pending      0 %       0 /       0 kB      NA     ]
[ ] rootfs       [pending      0 %       0 /       0 kB      NA     ]
[ ] mmc          [pending      0 %       0 /       0 kB      NA     ]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 10: Security failure

    image        [state    progress         transfer     flash speed]
---------------------------------------------------------------------
[f] cert-sw      [init         0 %       1 /       1 kB      NA     ]
[ ] cmt-2nd      [pending      0 %       0 /       0 kB      NA     ]
[ ] cmt-algo     [pending      0 %       0 /       0 kB      NA     ]
[ ] cmt-mcusw    [pending      0 %       0 /       0 kB      NA     ]
[ ] xloader      [pending      0 %       0 /       0 kB      NA     ]
[ ] secondary    [pending      0 %       0 /       0 kB      NA     ]
[ ] kernel       [pending      0 %       0 /       0 kB      NA     ]
[ ] rootfs       [pending      0 %       0 /       0 kB      NA     ]
[ ] mmc          [pending      0 %       0 /       0 kB      NA     ]
Fetching error list:
========================================
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
Downgrade disallowed (1326808332)
[Pipe   0] Finishing in error state with status 10
========================================

ERROR: Failed to flash images

Flashing finished at 13:29:37

Flashing unsuccessful
Press Enter to exit

I get the error that downgrade is disallowed. Is the device dead? I downloaded the file that @caco3 published in http://talk.maemo.org/showpost.php?p...&postcount=101, but I do not how to use it. Could anyone please give a hint?

Regards

Antonio

Last edited by antonioaraujob; 2013-01-12 at 14:11. Reason: Delete device identifier

The Following User Says Thank You to antonioaraujob For This Useful Post:
Wikiwide

Hurrian | # 105 | 2013-01-12, 03:36 | Report

If you flashed the N950 leaked PR1.3, NOLO disallows downgrades.

Just flash the leaked PR1.3 again with

Code:

flasher -f -F DFL61_HARMATTAN_40.2012.21-3_PR_LEGACY_RM680-OEM1-916_ARM.bin

peterleinchen | # 106 | 2013-01-12, 13:08 | Report

Originally Posted by antonioaraujob View Post

Dear friends,
I have a problem with my N950.
I decided to flash the device again following the steps in: http://harmattan-dev.nokia.com/release/N950-39-5/. I say again because I did the flash process a couple of months ago.

On what firmware you are?

Originally Posted by Hurrian View Post

If you flashed the N950 leaked PR1.3, NOLO disallows downgrades.

Downgrade always is disallowed.
But if he really uses PR1.3 he should know that.

I expect him to be on PR1.2
and from the link he posted in his thread he will get the PR1.1 firmware downloaded.
So maybe just visit the correct site
http://harmattan-dev.nokia.com/release/N950/firmware
to get the PR1.2?

Reread and found me confirmed

Originally Posted by

Found device RM-680, hardware revision 1124
NOLO version 2.3.6
Version of 'sw-release': DFL61_HARMATTAN_3.2012.02-6_PR_RM680
Erase done.
Image SW version DFL61_HARMATTAN_2.2011.39-5_PR_RM680
Downgrade disallowed (1326808332)

So go hunt for PR1.2 firmware files on above link and save it on local HD!

--edit
and maybe remove your IMEI twice from your post, antonio?

Last edited by peterleinchen; 2013-01-12 at 13:21.

The Following 3 Users Say Thank You to peterleinchen For This Useful Post:
antonioaraujob, Sourav.dubey, Wikiwide

antonioaraujob | # 107 | 2013-01-12, 14:17 | Report

Dear @peterleinchen, thanks a lot for your answer. Yes, you are right, I downloaded a wrong firmware, I had to use the link you say:

http://harmattan-dev.nokia.com/release/N950/firmware

to download the file:

http://harmattan-dev.nokia.com/relea...RM680-OEM1.bin.

I am downloading the file right now and I am going to flash the device again.

Also thanks for your comment about device identifier

This is a very good community

Best regards

Antonio

The Following User Says Thank You to antonioaraujob For This Useful Post:
Wikiwide

antonioaraujob | # 108 | 2013-01-12, 23:29 | Report

Dear @peterleinchen and people of the forum.

I downloaded the file:

http://harmattan-dev.nokia.com/relea...RM680-OEM1.bin

and I could reflash my N950 successfully.

Thanks for your help.

Best regards

Antonio

The Following 2 Users Say Thank You to antonioaraujob For This Useful Post:
peterleinchen, Wikiwide

smit | # 109 | 2014-01-01, 18:51 | Report

I had installed PR1.3 on my N950 from the leaked image here. I am facing same problem with cmt, similar to previous post but with PR1.3.

Code:

sudo flasher -F /media/smit/HDD/softwares/Nokia/N\ 950/Flasher/DFL61_HARMATTAN_40.2012.21-3_PR_LEGACY_RM680-OEM1-916_ARM.bin -f

flasher 3.12.1 (Oct  5 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

Suitable USB interface (bootloader/phonet) not found, waiting...
USB device found at bus 001, device address 026.
Device identifier: 357881040013536 (SN: N/A)
Found device RM-680, hardware revision 1124
NOLO version 2.3.6
Version of 'sw-release': DFL61_HARMATTAN_40.2012.21-3_PR_RM680
Sending ape-algo image (7096 kB)...
100% (7096 of 7096 kB, avg. 22316 kB/s)
Suitable USB interface (phonet) not found, waiting...
USB device found at bus 001, device address 027.
Device identifier: 357881040013536 (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-680 rev. 1124
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_RM680
Image moslo not present
Image mmc not present
Image tar skipped
Image config skipped

Battery level 16 %, continuing.

    image        [state    progress         transfer     flash speed]
---------------------------------------------------------------------
[x] cert-sw      [finished   100 %       1 /       1 kB      NA     ]
[x] cmt-2nd      [finished   100 %      95 /      95 kB      NA     ]
[_] cmt-algo     [init       100 %     789 /     789 kB      NA     ]
[ ] cmt-mcusw    [pending      0 %       0 /       0 kB      NA     ]
[x] xloader      [finished   100 %      23 /      23 kB      NA     ]
[x] secondary    [finished   100 %      90 /      90 kB      NA     ]
[x] kernel       [finished   100 %    2714 /    2714 kB    1993 kB/s]
[_] rootfs       [writing      0 %   37888 /  762871 kB    1407 kB/s]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 1: Unknown error

    image        [state    progress         transfer     flash speed]
---------------------------------------------------------------------
[x] cert-sw      [finished   100 %       1 /       1 kB      NA     ]
[x] cmt-2nd      [finished   100 %      95 /      95 kB      NA     ]
[f] cmt-algo     [init         0 %     789 /     789 kB      NA     ]
[-] cmt-mcusw    [pending      0 %       0 /       0 kB      NA     ]
[x] xloader      [finished   100 %      23 /      23 kB      NA     ]
[x] secondary    [finished   100 %      90 /      90 kB      NA     ]
[x] kernel       [finished   100 %    2714 /    2714 kB    1993 kB/s]
[x] rootfs       [finished   100 %  762871 /  762871 kB    9184 kB/s]
Fetching error list:
========================================
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
Timeout while waiting for the HWBREAK
Could not reboot into cold bootmode
[Pipe   6] Finishing in error state with status 1
Client SUD failed to handle message 0x88:0x08
========================================

ERROR: Failed to flash images

For N950 PR1.3, there is only one image available here. Is there any other place where I can download different variant of PR1.3 for N950?

XenGi | # 110 | 2014-01-01, 19:59 | Report

Just follow the guide from thp.

http://thp.io/2013/maemo/n950_mini_reflash_guide.html