Page 57 of 156 « First 475556 57 585967 Last »
Reply
Thread Tools
H2O is offline H2O
2013-03-06 , 08:12
Posts: 6 | Thanked: 0 times | Joined on Mar 2013 @ Switzerland
#561
My nokia N9(switzerland – 059k748) turned off by itself one fine day and it went into a boot-loop(starts up with nokia logo and turns off, and that keeps going on like that). Then i thought of flashing the device. I used Navifirm 1.7 to download the respective firmware for my device. Then using flasher 3.12.1 i tried flashing it. But im getting errors in the process. i tried several times re-downloading the firmware and flashing again. I have even tried flashing it with another country specific firmware but had no luck. All i see from the first place now is a warning screen when the phone is started up or is plugged into the usb port.

Here is the error screen i see:

WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

Suitable USB interface (bootloader/phonet) not found, waiting…
USB device found at bus 002, device address 045.
Device identifier: 357923041060460 (SN: N/A)
Found device RM-696, hardware revision 1507
NOLO version 2.3.6
Version of ‘sw-release’: DFL61_HARMATTAN_40.2012.21-3_PR_009
Sending ape-algo image (7096 kB)…
100% (7096 of 7096 kB, avg. 31125 kB/s)
Suitable USB interface (phonet) not found, waiting…
USB device found at bus 002, device address 046.
Device identifier: 357923041060460 (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1507
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_009
Image moslo not present
Image mmc not present
Image tar skipped
Image config skipped

Battery level 80 %, continuing.

image [state progress transfer flash speed]
———————————————————————
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[_] cmt-mcusw [finishing 25 % 6050 / 6050 kB 3158 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 1971 kB/s]
[_] rootfs [finishing 100 % 32768 / 1170206 kB NA ]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 1: Unknown error

image [state progress transfer flash speed]
———————————————————————
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[x] cmt-mcusw [finished 100 % 6050 / 6050 kB 3158 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 1971 kB/s]
[f] rootfs [finishing 0 % 32768 / 1170206 kB NA ]
Fetching error list:
========================================
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
mmc: sfdisk returned status 1
mmc: Could not exec ‘tune2fs -L rootfs /tmp/sudmmcGDmzw0/internal0p2′
mmc: Could not remove mount directory /tmp/sudmmcGDmzw0/mnt: No such file or directory
[Pipe 4] Finishing in error state with status 1
========================================

ERROR: Failed to flash images

I have tried this on both windows as well as on linux and get the same result. Any help from anyone is greatly appreciated.

Thanks in advance
 
thedead1440 is offline thedead1440
2013-03-06 , 08:16
Moderator | Posts: 6,215 | Thanked: 6,402 times | Joined on Nov 2011
#562
H2O,

I'm not 100% sure but iirc that error requires emmc being flashed too or your previous firmware's cmt-mcusw being flashed.

If its emmc you may want to take out all your data first by mounting the phone using juiceme's telnet

Maybe do a bit of searching on this thread your error may have happened to someone else before...
 
H2O is offline H2O
2013-03-06 , 08:25
Posts: 6 | Thanked: 0 times | Joined on Mar 2013 @ Switzerland
#563
Originally Posted by thedead1440 View Post
H2O,

I'm not 100% sure but iirc that error requires emmc being flashed too or your previous firmware's cmt-mcusw being flashed.

If its emmc you may want to take out all your data first by mounting the phone using juiceme's telnet

Maybe do a bit of searching on this thread your error may have happened to someone else before...
I have tried that as well infact. I have individually tried all the following command to see if atleast one works:

1. flasher -F main.bin -f
2. flasher -F main.bin -F emmc.bin -f (with -R as well)
3. flasher -F main.bin -f --flash-only=rootfs, cmt (arguments taken individually as well)

No clue on what to do now. Thanks anyways
 
thedead1440 is offline thedead1440
2013-03-06 , 08:41
Moderator | Posts: 6,215 | Thanked: 6,402 times | Joined on Nov 2011
#564
Can you try doing:

Code:
flasher -f -F rootfs.bin -F emmc.bin --no-preserve -R
Post the output please. Thanks!
 

The Following User Says Thank You to thedead1440 For This Useful Post:
H2O is offline H2O
2013-03-06 , 08:49
Posts: 6 | Thanked: 0 times | Joined on Mar 2013 @ Switzerland
#565
Originally Posted by thedead1440 View Post
Can you try doing:

Code:
flasher -f -F rootfs.bin -F emmc.bin --no-preserve -R
Post the output please. Thanks!
Will do it right away and post the output. I assume rootfs to be the mainFirmwareFile.bin. I will rename it to rootfs and try as you said.

will be right back with the result.
 
thedead1440 is offline thedead1440
2013-03-06 , 08:55
Moderator | Posts: 6,215 | Thanked: 6,402 times | Joined on Nov 2011
#566
Indeed rootfs.bin == mainFirmwareFile.bin
 
H2O is offline H2O
2013-03-06 , 09:05
Posts: 6 | Thanked: 0 times | Joined on Mar 2013 @ Switzerland
#567
Originally Posted by thedead1440 View Post
Indeed rootfs.bin == mainFirmwareFile.bin
No luck

OUTPUT:

flasher 3.12.1 (Oct 5 2011) Harmattan
Warning: --no-preserve is not recommended, instead use erase commands
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

Suitable USB interface (bootloader/phonet) not found, waiting...
USB device found at bus 002, device address 003.
Device identifier: 357923041060460 (SN: N/A)
Found device RM-696, hardware revision 1507
NOLO version 2.3.6
Version of 'sw-release': DFL61_HARMATTAN_40.2012.21-3_PR_009
Sending ape-algo image (7096 kB)...
100% (7096 of 7096 kB, avg. 30989 kB/s)
Suitable USB interface (phonet) not found, waiting...
USB device found at bus 002, device address 004.
Device identifier: 357923041060460 (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1507
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_009
Image moslo not present
Image tar skipped
Image config skipped

Battery level 95 %, continuing.

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[_] cmt-mcusw [finishing 0 % 6050 / 6050 kB 3158 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 1974 kB/s]
[_] rootfs [finishing 100 % 32768 / 1170206 kB NA ]
[ ] mmc [pending 0 % 0 / 0 kB NA ]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 1: Unknown error

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[x] cmt-mcusw [finished 100 % 6050 / 6050 kB 3158 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 1974 kB/s]
[f] rootfs [finishing 0 % 32768 / 1170206 kB NA ]
[-] mmc [pending 0 % 0 / 0 kB NA ]
Fetching error list:
========================================
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
mmc: sfdisk returned status 1
mmc: Could not exec 'tune2fs -L rootfs /tmp/sudmmcMI74M0/internal0p2'
mmc: Could not remove mount directory /tmp/sudmmcMI74M0/mnt: No such file or directory
[Pipe 4] Finishing in error state with status 1
========================================

ERROR: Failed to flash images
 
thedead1440 is offline thedead1440
2013-03-06 , 09:16
Moderator | Posts: 6,215 | Thanked: 6,402 times | Joined on Nov 2011
#568
Hmm that error maybe due to corrupted .bin files or broken flash memory. Have you tried redownloading the .bin files? Also flashing another 009 pr_legacy variant?
 
H2O is offline H2O
2013-03-06 , 09:35
Posts: 6 | Thanked: 0 times | Joined on Mar 2013 @ Switzerland
#569
Originally Posted by thedead1440 View Post
Hmm that error maybe due to corrupted .bin files or broken flash memory. Have you tried redownloading the .bin files? Also flashing another 009 pr_legacy variant?
yes, I have tried redownloading and flashing it several times. I have even tried the 009 variant of germany and norway as well. I guess this is the latest firmware and hence now i cant move forward nor backward - as downgrading is blocked by the flasher(even tried that)
 
cong is offline cong
2013-03-13 , 13:42
Posts: 3 | Thanked: 0 times | Joined on Mar 2013
#570
Originally Posted by H2O View Post
No luck

OUTPUT:

flasher 3.12.1 (Oct 5 2011) Harmattan
Warning: --no-preserve is not recommended, instead use erase commands
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

Suitable USB interface (bootloader/phonet) not found, waiting...
USB device found at bus 002, device address 003.
Device identifier: 357923041060460 (SN: N/A)
Found device RM-696, hardware revision 1507
NOLO version 2.3.6
Version of 'sw-release': DFL61_HARMATTAN_40.2012.21-3_PR_009
Sending ape-algo image (7096 kB)...
100% (7096 of 7096 kB, avg. 30989 kB/s)
Suitable USB interface (phonet) not found, waiting...
USB device found at bus 002, device address 004.
Device identifier: 357923041060460 (SN: N/A)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1507
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_009
Image moslo not present
Image tar skipped
Image config skipped

Battery level 95 %, continuing.

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[_] cmt-mcusw [finishing 0 % 6050 / 6050 kB 3158 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 1974 kB/s]
[_] rootfs [finishing 100 % 32768 / 1170206 kB NA ]
[ ] mmc [pending 0 % 0 / 0 kB NA ]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 1: Unknown error

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[x] cmt-algo [finished 100 % 789 / 789 kB NA ]
[x] cmt-mcusw [finished 100 % 6050 / 6050 kB 3158 kB/s]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 1974 kB/s]
[f] rootfs [finishing 0 % 32768 / 1170206 kB NA ]
[-] mmc [pending 0 % 0 / 0 kB NA ]
Fetching error list:
========================================
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
mmc: sfdisk returned status 1
mmc: Could not exec 'tune2fs -L rootfs /tmp/sudmmcMI74M0/internal0p2'
mmc: Could not remove mount directory /tmp/sudmmcMI74M0/mnt: No such file or directory
[Pipe 4] Finishing in error state with status 1
========================================

ERROR: Failed to flash images
same too, help me ????
 
Reply
Page 57 of 156 « First 475556 57 585967 Last »

Tags
flashing, nokia n9

« Previous Thread | Next Thread »

 
Forum Jump


All times are GMT. The time now is 08:56.

Contact Us - Home - Archive - Top