TOHKBD rev2 - Page 153 - maemo.org

ssahla | # 1521 | 2015-07-09, 11:54 | Report

My tohkbd's TOH part didn't fit the phone very well when I received it; that is, the middle holder on the button side didn't "snap in", resulting in the TOH being a bit loose on that side, with a small gap in the middle. When examining the TOH I noticed that the fitting of the circuit board into the TOH was so tight that when the board was in place, it bent the side of the TOH outward ever so slightly, and as a result, one of the little bumps in the TOH didn't get caught in the corresponding hole on the phone side.

So, I took the board out of the TOH, carefully sandpapered a little bit out of its left and right side, and put it back. Now the TOH snaps in properly. And the board is not loose or anything, it still fits in snugly and stays in place.

So, good thing it wasn't glued!

The Following 8 Users Say Thank You to ssahla For This Useful Post:
Amboss, cproc, Feathers McGraw, ggabriel, Jordi, juiceme, mosen, tetris11_

kimmoli | # 1522 | 2015-07-09, 19:51 | Report

TOHKBD2 0.4.1 In Harbour QA:

0.4.1 Fixes caps-lock issue

Changes 0.3.0 --> 0.4.0 :
- Bug fixes
- Add sticky shift and lock mode for all modifiers. move - - CapsLock to Sym+Caps
- Ctrl-alt-backspace restarts lipstick with remorse
- Ctrl-alt-del reboots phone with remorse
- Follow system capslock led state
- Pulldown menu for restoring default general settings
- Sort taskswitcher apps by 'mru'
- Sym+Home toggles backlight always on / auto

http://repo.merproject.org/obs//home....1.armv7hl.rpm

If the link does not work, there might already be a newer release

Thanks for community debugging issues, suggestions and translations !

Last edited by kimmoli; 2015-07-10 at 16:23.

The Following 23 Users Say Thank You to kimmoli For This Useful Post:
Amboss, cproc, eekkelund, explit, Feathers McGraw, ggabriel, hhbbap, HtheB, Jordi, juiceme, Kabouik, malkavian, minimos, mosen, mrsellout, mscion, OVK, pichlo, rcolistete, rooster13, Tsippaduida, vistaus, zagrim

misterc | # 1523 | 2015-07-10, 14:23 | Report

drivers, instructions, ANYTHING?
maybe in the 1st post?

EDIT: rebooted a couple times and removed / added TOHKBD a couple times did the trick
now... backlit doesn't work properly (see pic attached)
Ctrl+C doesn't work (neither of the two)

Attached Images

Last edited by misterc; 2015-07-10 at 14:53.

The Following User Says Thank You to misterc For This Useful Post:
juiceme

Kabouik | # 1524 | 2015-07-10, 14:43 | Report

I don't have a tohkbd yet (and I'm leaving for holidays

) so I can't tell for sure, but I think the software installs automatically when you snap the toh on. You shouldn't need any instructions except if you want pre-releases. Please excuse me tohkbd team if I'm wrong.

The Following User Says Thank You to Kabouik For This Useful Post:
vistaus

ssahla | # 1525 | 2015-07-10, 14:48 | Report

Originally Posted by misterc View Post

drivers, instructions, ANYTHING?
maybe in the 1st post?

https://together.jolla.com/question/96836/tohkbd-faq/

The Following 2 Users Say Thank You to ssahla For This Useful Post:
juiceme, vistaus

bennypr0fane | # 1526 | 2015-07-10, 15:31 | Report

Originally Posted by PekkU View Post

Is there any plans getting suggestions available even from a single dictionary? Now that the virtual keyboard is hidden when using TOHBD also the language selection and suggestions are hidden.

Actually, it's still not completely hidden. There is this completely blank, slim bar at the bottom. If we can't make it disappear, maybe it can be made useful, showing the suggestions there?

Last edited by bennypr0fane; 2015-07-10 at 17:30.

The Following 3 Users Say Thank You to bennypr0fane For This Useful Post:
juiceme, pichlo, vistaus

bennypr0fane | # 1527 | 2015-07-10, 15:34 | Report

https://together.jolla.com/question/96836/tohkbd-faq/
This is very incomplete.

Originally Posted by

Q6: I have AZERTY/QWERTZ layout, but i get qwerty characters when i type with it?

Or rather: How long before I can use my QWERTZ like a QWERTZ?

Much more work is necessary on the software. Some of it will only be effective with SfOS 2.

Last edited by bennypr0fane; 2015-07-10 at 17:32.

The Following 2 Users Say Thank You to bennypr0fane For This Useful Post:
juiceme, mosen

evadim | # 1528 | 2015-07-10, 17:22 | Report

Originally Posted by bennypr0fane View Post

https://together.jolla.com/question/96836/tohkbd-faq/
This is very incomplete.

Or rather: How long before I can use my QWERTZ like a QWERTZ?

I think, even more interesting question - how to write in second language, as I can't swithch layout at all? I already think about uninstalling software and use TOHKBD as awesome fridge magnet

mrsellout | # 1529 | 2015-07-10, 17:33 | Report

Originally Posted by bennypr0fane View Post

https://together.jolla.com/question/96836/tohkbd-faq/
This is very incomplete.

Or rather: How long before I can use my QWERTZ like a QWERTZ?

The answers for for Questions 5,6,10, and 13 are all grouped, ie.

Originally Posted by

A: Jolla Sailfish 1.1.6.27 version (and older) does not support changing keyboard layout. We need to wait for sailfish update. Current layout does not support compose or special chars outside of pc-105 US layout. The settings are grayed out becaused they do not work yet.

Last edited by mrsellout; 2015-07-10 at 17:33. Reason: typo

The Following 3 Users Say Thank You to mrsellout For This Useful Post:
bennypr0fane, Feathers McGraw, pichlo

Henque19 | # 1530 | 2015-07-10, 22:14 | Report

Sorry if this has already been covered, but I just installed the latest version from Jolla store. Layout switching works, but ['; instead of åäö on the scandic layout and similar with the german layout.
I'm guessing it's a known issue, but I wanted to ask just to make sure..