Page 1 of 2 1 2
Reply
Thread Tools
Nick999999 is offline Nick999999
2016-08-22 , 20:38
Posts: 6 | Thanked: 6 times | Joined on Aug 2016
#1
So I found my N9 which I had kept in a box somewhere because it had died and wasnt getting detected by the computer and I had switched to android in the mean time.

I wanted to recover it for the sake of the good old days so I hooked it up to the pc just for the heck of it and voila it is getting detected ,though since the battery was dead I tired using:

flasher -i in hopes of charging it but that does nothing.

So I went ahead and tried

flasher -f -F rootfs.bin -F nomaps.bin --flash-only=mmc

This charges the phone thankfully but then it finishes the flashing and the phone is stuck in a reboot loop, the screen doesent even light up ( the led goes from fait to a bright white and then turns off and repeats the process)

Any help would be appreciated.

PS: Since it almost impossible to find the exact firmare anyomre I'm using the below mentioned files from here http://talk.maemo.org/showpost.php?p...00&postcount=1
DFL61_HARMATTAN_40.2012.21-3_PR_LEGACY_001-OEM1-958 and
DFL61_HARMATTAN_40.2012.13-7.NOMAPS_EMMC_NOMAPS

My device variant is 059j1z5 16 GB



Code:
C:\Program Files\Nokia\Flasher>flasher -f -F rootfs.bin -F nomaps.bin --flash-only=mmc
flasher 3.12.1 (Oct  6 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

Suitable USB interface (bootloader/phonet) not found, waiting...
Found device RM-696, hardware revision 1507
NOLO version 2.3.6
Version of 'sw-release': DFL61_HARMATTAN_40.2012.21-3_PR_001
Sending ape-algo image (7096 kB)...
100% (7096 of 7096 kB, avg. 27085 kB/s)
Suitable USB interface (phonet) not found, waiting...
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1507
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_001
Image cmt-2nd skipped
Image cmt-algo skipped
Image cmt-mcusw skipped
Image xloader skipped
Image secondary skipped
Image kernel skipped
Image moslo skipped
Image rootfs skipped
Image tar skipped
Image config skipped
Charging battery, 10 % battery level (11 % required). Ctrl-c to exit
Battery level 11 %, continuing.

    image        [state    progress         transfer     flash speed]
---------------------------------------------------------------------
[x] cert-sw      [finished   100 %       1 /       1 kB      NA     ]
[x] mmc          [finished   100 %  261587 /  261587 kB   17371 kB/s]
Success
 

The Following User Says Thank You to Nick999999 For This Useful Post:
n0x is offline n0x
2016-08-22 , 21:56
Posts: 59 | Thanked: 59 times | Joined on Nov 2012 @ Philippines
#2
Try flashing the rootfs.bin only first before flashing the emmc.bin

It might be that some files needed by some of your apps in rootfs were lost by reformatting the emmc and thus the bootloops
 

The Following User Says Thank You to n0x For This Useful Post:
Nick999999 is offline Nick999999
2016-08-22 , 23:00
Posts: 6 | Thanked: 6 times | Joined on Aug 2016
#3
Originally Posted by n0x View Post
Try flashing the rootfs.bin only first before flashing the emmc.bin

It might be that some files needed by some of your apps in rootfs were lost by reformatting the emmc and thus the bootloops
Thanks I did that now I can feel the vibrations on boot and even the nokia startup music,sadly the screen still does not power on.It stays off.

Last I checked a year or more ago perhaps the screen was working fine.I guess its a screen issue.So long to an old friend.Back in the box it goes.
 

The Following User Says Thank You to Nick999999 For This Useful Post:
aspergerguy is offline aspergerguy
2016-08-23 , 13:01
Posts: 699 | Thanked: 1,439 times | Joined on Aug 2014
#4
Do you have any luck booting if you enable R & D mode first?

flasher --enable-rd-mode --set-rd-flags=no-lifeguard-reset
 

The Following User Says Thank You to aspergerguy For This Useful Post:
chilango is offline chilango
2016-08-23 , 14:58
Posts: 508 | Thanked: 623 times | Joined on Jul 2012 @ Mexico/Germany
#5
Leave it some time. I had some month ago the same (after starting no UI). Some reboots doesnt change the behavior. Than i put it on and leave on the table but with charger.

After one or two hours the screen came up and everything was fine again
 

The Following User Says Thank You to chilango For This Useful Post:
Nick999999 is offline Nick999999
2016-08-24 , 04:38
Posts: 6 | Thanked: 6 times | Joined on Aug 2016
#6
Originally Posted by aspergerguy View Post
Do you have any luck booting if you enable R & D mode first?

flasher --enable-rd-mode --set-rd-flags=no-lifeguard-reset
I already have it enabled,still no luck with the screen.It just does not light up. I can feel the boot vibrations and nokia startup music but no life on the screen, its completely off.
 

The Following User Says Thank You to Nick999999 For This Useful Post:
Nick999999 is offline Nick999999
2016-08-24 , 04:40
Posts: 6 | Thanked: 6 times | Joined on Aug 2016
#7
Originally Posted by chilango View Post
Leave it some time. I had some month ago the same (after starting no UI). Some reboots doesnt change the behavior. Than i put it on and leave on the table but with charger.

After one or two hours the screen came up and everything was fine again
By no UI you mean the screen was completely off? not even the backlight? coz in my case even though I can feel the boot vibrations and nokia startup music but no life on the screen, its totally off like when you turn off the phone kinda off.
 

The Following User Says Thank You to Nick999999 For This Useful Post:
juiceme is offline juiceme
2016-08-24 , 07:40
Community Council | Posts: 4,902 | Thanked: 12,827 times | Joined on May 2012 @ Southerrn Finland
#8
One thing comes to mind; if you cannot ssh to the device at least what I'd do is to login to it via the serial connection.
Then you could enable ssh and vnc and see what's going on in the display
 
Nick999999 is offline Nick999999
2016-08-24 , 09:24
Posts: 6 | Thanked: 6 times | Joined on Aug 2016
#9
Originally Posted by juiceme View Post
One thing comes to mind; if you cannot ssh to the device at least what I'd do is to login to it via the serial connection.
Then you could enable ssh and vnc and see what's going on in the display
Can you point me to a thread or tutorial that shows how to go about doing that?
 

The Following User Says Thank You to Nick999999 For This Useful Post:
nieldk is offline nieldk
2016-08-24 , 09:55
Posts: 1,255 | Thanked: 4,243 times | Joined on Oct 2014
#10
Look at this picturr, and schematics

https://talk.maemo.org/showthread.php?t=82571

I believe you also need a custom kernen, with additional boot parameters
Attached Images
 
__________________
You can still support my work by donation - click here

ETH: 0xFcD031609DB739C62730589361940C68ceEbC913
 

The Following 2 Users Say Thank You to nieldk For This Useful Post:
Reply
Page 1 of 2 1 2

« Previous Thread | Next Thread »

 
Forum Jump


All times are GMT. The time now is 07:25.

Contact Us - Home - Archive - Top