I installed NITDroid for the first time and things that I noticed are:
- market didn't work from beginning (endless downloading), but now, from unknown reason to me, it works
- phone is much warmer, compared running under maemo OS
- "up arrow" doesn't work
Is it possible to somehow fix this "up arrow" bug?
but i chose 4 in the bootmenu but i cant connect to my wifi. i entered my wep key but it keeps downloading the ip-adress and then it goes back to scanning.
it keeps going in a loop
Ok, i had that kind of problem after i did the new update...
Then try this:
Just do this again in xterm:
mkdir /and (if error comes, just proceed)
mount -o noatime,rw /dev/mmcblk1p2 /and
cd /and
rm -rf *
bzcat /home/user/MyDocs/NITDroid-N900-0.0.5-3-BIG.tbz2 | tar xvf -
cd /and/system/bin
nano load_modules.sh (here you type your bluetooth number: BDADDR="0cddef0a0e6d")
cd /
umount /and
That fixed it for me... seemed like the old NITdroid build didn't get fully ereased the first time
Get a file manager from Android Market, navigate to root>extras and open it from there.
That did work thanks
One thing though the trailer on gametralirs.com did the buffering and just when it seemed to start the web crashed?
Anybody know of any sites that uses flashplayer 10.1 so i can test the flashplayer further to see if it crashes there to
e: Before gametrailers switched to 10.1 i wasn't able to watch trailers either from maemo microb, it allways hanged on the buffering, maybe it's just a to heavy site to cope for the N900's hardware?
its possible its too heavy to handle on the ntidroid build as is (ie with no hardware assistance to gfx)
edit: the toystory3.com is one i use to test flash worked
its possible its too heavy to handle on the ntidroid build as is (ie with no hardware assistance to gfx)
edit: the toystory3.com is one i use to test flash worked
steve,
i'm having a problem with wifi in the latest build.
i can enter my wep key and then it wants to get my ip-adress and then it disconnects, then scanning and then trying to get the ip-adress again.
and then it starts over and over.
in the install i changed the mac id to my one id
install Flasher 3.5 (windows 32bits)
go to flasher folder by use Windows Key+R (run) type CMD - Enter
in CMD: cd c:\program (press tab)\ maemo\flasher (press tab)
you should get this line:
cd "C:\Program Files\maemo\flasher-3.5"
Take the battery out of the phone for 10seconds, put it back in and press hold "U" button then plug in the microUSB.
in CMD: type this (assuming that you've downloaded those files already and put them in flasher folder in C-drive.)
(command below will format your eMMC, be sure to back up everything before doing so).
You should get something like this: I reflashed mine just now lol. Because of i want my device to be cleaned again.
----------------------------------------------
----------------------------------------------
Image 'mmc', size 255947 kB
Version RX-51_2009SE_10.2010.13-2.VANILLA
USB device found found at bus bus-0, device address \\.\libusb0-0001--0x0421-0x0
105.
Found device RX-51, hardware revision 2101
NOLO version 1.4.14
Version of 'sw-release': <no version>
Booting device into flash mode.
Suitable USB device not found, waiting.
USB device found found at bus bus-0, device address \\.\libusb0-0001--0x0421-0x0
1c8.
Raw data transfer EP found at EP2.
Image(s) flashed successfully in 34.958 s (7321 kB/s)!
If you are really using WEP try it without encryption. It makes no difference for a hacker (even a N900 can hack WEP networks easily) and is easier to set up. (It would still be better to change to WPA2).
