nicholes | # 1 | 2010-11-14, 09:58 | Report

using xp 32bit successfully flashed the firmware

and when i try to flash emmc immidiatly after frimware flshing(the device was booted between both flashing)gives me..

[Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

C:\Program Files\maemo\flasher-3.5>flasher-3.5.exe -F RX-51_2009SE_10.2010.13-2.
VANILLA_PR_EMMC_MR0_ARM.bin -f -R
flasher v2.5.2 (Sep 24 2009)

Image 'mmc', size 255947 kB
Version RX-51_2009SE_10.2010.13-2.VANILLA
USB device found found at bus bus-0, device address \\.\libusb0-0001--0x0421-0x0
105.
Found device RX-51, hardware revision 2204
NOLO version 1.4.14
Version of 'sw-release': RX-51_2009SE_20.2010.36-2.004_PR_004
Booting device into flash mode.
Suitable USB device not found, waiting.

and in the last tried without -R paramiter(for not reebooting the device between the both flashing) successfully flashed the firmware but gets the same in emmc

neotalk | # 2 | 2010-11-14, 10:25 | Report

RX-51_2009SE_20.2010.36-2_PR_COMBINED_MR0_ARM
RX-51_2009SE_10.2010.13-2.VANILLA_PR_EMMC_MR0_ARM

these are the images i used. did you place them in the flasher directory?

ossipena | # 3 | 2010-11-14, 10:41 | Report

is the device stuck on 5 balloons -screen?

e: the images are in the right place as you can see from output pasted to first post.

asidana | # 4 | 2010-11-14, 10:58 | Report

happened to me when i wanted to flash vanilla after flashing pr1.3 tried few times and gave up

nicholes | # 5 | 2010-11-15, 12:05 | Report

yes i place them in falsher directory!

nicholes | # 6 | 2010-11-15, 12:05 | Report

yes the device stuck on 5 baloonscreen!

James_Littler | # 7 | 2010-11-15, 12:09 | Report

You don't want it booting after the firmware so you were correct to drop -R from the first command.

Try yanking the USB from the PC and plugging it into another port when it gets stuck.
This has corrected the problem for me in the past. Eventually you'll find a port that will always(ish) work.

If you hit a real dead end, run Ubuntu from a live USB/CD and try flashing from the terminal within Ubuntu.

tusharmax | # 8 | 2010-11-15, 12:13 | Report

did u wait for some time for emmc to start flashing, cuz it takes around 10 sec for flashing process to start after this mssg is displayed "suitable usb device not found"


anyways major issues are cuz of flashing in windows , flashing via linux is da easiest and error free.

nicholes | # 9 | 2010-11-15, 12:17 | Report

tried changing usb prot too !!did not work for me ..xcept using unbuntu live usb/cd .what can i try as the last option?

zarf | # 10 | 2010-11-15, 12:25 | Report

I'd start from scratch.

I turned n900 off, got flasher waiting to flash kernal without the -R option, then plugged it in, and turned it on while holding the u key.

when it had finished, I didn't touch or reboot anything, just fed in the vanilla flash command and let it go

try that, should work as it blanks everything

I'm running vista