Reply
Thread Tools
Posts: 4 | Thanked: 0 times | Joined on Sep 2012 @ Hellas
#311
Hi people, i would like your help.
My N9 has the following product: 059L7Z9: N9 RM-696 PTK Centertel (Orange PL) PL (black) v1 - MR

and its on PR1.2 When i started working with it a new update notification came up. i started the update proccess and after downloading it at 70% failed and n9 reboots.
Since then i tried everything to put PR1.3
So my question is, looking navifirm that i dont have an original update for PR1.3?? I tried flashing other fw but failed. all i got is error 10
tried these fw:

059J204
059J1W1

any suggestions?

Thanks in advance
 
Posts: 1 | Thanked: 0 times | Joined on Sep 2012
#312
Originally Posted by gaggar View Post
Yesterday my N9 started acting wierd...
suddently it:
lost all signal
camera coudn't launch
restarted by itself.

Once it had sartet up it wrote something like "there is something wrong with your sim-card" /
at other times is says "an error has occured cannot connect to network - Contact Nokia store"

I tried using my simcard in another phone - and it workes fine - so it's not the simcard causing this, i think.

Then i figured that it could be a software problem, så first i tried to:

Restore Settings, do the following:

Open “Settings”
Tap “Reset”
Choose “Restore Settings”
Tap “Yes” to confirm the process.

Still got the message "there is something wrong with your sim-card".

then i tried:

To Clear Device, do the following:

Open “Settings”
Tap “Reset”
Choose “Clear Device”
Tap “Yes” to confirm the process.

still got the same message once starting up.

Finally i tried to flash it following the steps in this guide...i used the """""""Flasher -f -F rootfs.bin -F emmc.bin -R"""""""" thing..

The result was this:




Microsoft Windows XP [version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

C:\Programmer\Nokia\Flasher>Flasher -f -F pr1.2.bin -F emmc.bin -R
flasher 3.12.1 (Oct 6 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

Suitable USB interface (bootloader/phonet) not found, waiting...
Found device RM-696, hardware revision 1501
NOLO version 2.3.6
Version of 'sw-release': DFL61_HARMATTAN_30.2012.07-1_PR_001
Sending ape-algo image (7096 kB)...
100% (7096 of 7096 kB, avg. 16238 kB/s)
Suitable USB interface (phonet) not found, waiting...
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1501
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_30.2012.07-1_PR_001
Image moslo not present
Image tar skipped
Image config skipped

Battery level 20 %, continuing.

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[_] cmt-algo [init 100 % 789 / 789 kB NA ]
[ ] cmt-mcusw [pending 0 % 0 / 0 kB NA ]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 2401 kB/s]
[_] rootfs [writing 3 % 39936 / 1163796 kB 8053 kB/s]
[ ] mmc [pending 0 % 0 / 0 kB NA ]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 1: Unknown error

image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[f] cmt-algo [init 0 % 789 / 789 kB NA ]
[-] cmt-mcusw [pending 0 % 0 / 0 kB NA ]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 2401 kB/s]
[x] rootfs [finished 100 % 1163796 / 1163796 kB 9780 kB/s]
[x] mmc [finished 100 % 1627169 / 1627169 kB 9369 kB/s]
Fetching error list:
========================================
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
Timeout while waiting for the HWBREAK
Could not reboot into cold bootmode
[Pipe 6] Finishing in error state with status 1
========================================

ERROR: Failed to flash images

C:\Programmer\Nokia\Flasher>


My phone is a black 64GB bought in denmark - product code 059J187

PLEASE HELP.....it's driving CRAZY!!!!
Does anyone get a solution for this error?
I have the same, it's seems to coming from the "CMT part" of the flash. I have found a solution to flash only CMT with oldest version but i try to do it with vers 1.3 to 1.2 and 1.1 and it does not work!

Thanks!
 
Posts: 20 | Thanked: 1 time | Joined on Sep 2012
#313
Hello Guys.

Just a simple question. I have N9 Black with 16GB with Switzerland Swisscom branding.

I flashed my N9 with MacFlasher with the First Fimware from this Site:

http://www.btusers.com.ar/nan/nokia/...m=40.2012.21.3

I Flashed ROW Black.
Is this correct? Or should i scroll down and Flash Switzerland Firmware.

What is the difference of these two Firmwares?
 
Moderator | Posts: 6,215 | Thanked: 6,400 times | Joined on Nov 2011
#314
Are you on pr1.2 currently or pr1.3?

If the former you can flash with ROW Black; if the latter check your pr legacy is it 001; if not then you can't proceed...
 
Posts: 20 | Thanked: 1 time | Joined on Sep 2012
#315
Actually i was on PR1.1 and checking for updates it didn't find anything. PR1.3 is OUT and i coudn't recieve it.

Someone told me that my provider (Swisscom) won't push OTA Update. So i was stuck on PR1.1. Then i decided to flash manually to PR1.3

Last week i flashed ROW Firmware PR1.3(i don't know what this means) from the Website above.

Now i see there is also Switzerland Firmware if you scroll down.
My product Code is: 059L6C2.

So i don't know is this ROW Firmware OK for me or should i flash something else.
 
Moderator | Posts: 6,215 | Thanked: 6,400 times | Joined on Nov 2011
#316
Stick to ROW Firmware...Its honestly the better option...
 
Posts: 20 | Thanked: 1 time | Joined on Sep 2012
#317
Thanks.

Actually this is my Original Version:

059L6C2: N9 RM-696 Swisscom CH Black 16GB V1

For this Product Code there is still no Update for PR1.2 or PR1.3.

If i want to sell it i can still flash back to Original.
 
Posts: 4 | Thanked: 0 times | Joined on Sep 2012 @ Hellas
#318
Originally Posted by thedead1440 View Post
Stick to ROW Firmware...Its honestly the better option...
I'm going to try that too. Should i flash emmc also? or can i flash only the fw?

thanks in advance
 
Moderator | Posts: 6,215 | Thanked: 6,400 times | Joined on Nov 2011
#319
If you are doing a fresh flash to pr1.3 its recommended to do a full flash of rootfs+emmc...Make sure you have backed up your data to a PC first...
 

The Following User Says Thank You to thedead1440 For This Useful Post:
Posts: 4 | Thanked: 0 times | Joined on Sep 2012 @ Hellas
#320
Guess i cant install PR1.3

"If you previously upgraded your phone "over the air" (through SSU) and now receive a Downgrade disallowed error when flashing, try flashing an image with a higher variant code. For example, if you experienced the error with variant 001, try using variant 005 instead."

I dont understand what this means! I tried so many fw and always receive the following error. Currently i dont know what to do!



My C.V is PR1.2 only (its from Orange PL but im from Greece) guess this has something to do but i was convinced that i could flash a proper PR1.3 FW cause i read this int the first post:

"Nokia recommends always using the latest firmware image for your phone's product code (printed on the SIM card tray). This is the safest option. However, you may wish to change to a different variant than what shipped with the phone for the following reasons:

Receiving updates sooner - new firmware versions are normally released for the 001 variant first
Removing carrier branding - installing 00x variant firmware makes your subsidized N9 act just like an unlocked one"


what can i do?
 
Reply

Tags
flashing, nokia n9


 
Forum Jump


All times are GMT. The time now is 20:27.