[Announce] Cleven - an aircrack gui - Page 52 - maemo.org

m.mostafa1991 | # 511 | 2012-03-29, 02:05 | Report

Originally Posted by Estel View Post

You have to read one post before Yours, or, if You don't feel lazy, at least last page of thread, where you're posting...
---

As for merit, I think Saturn is quite busy now, so we must wait a little more for proper solution.

/Estel

ok thanks !

i'll wait

sepehr_se | # 512 | 2012-03-29, 18:48 | Report

in 2.4-8 version when I pressed the capture terminal opens and the beacone increase and nothing happend anymore.what should I do?

pawelstryju | # 513 | 2012-03-29, 21:17 | Report

@Estel: Does injection works for you?
because I only replaced files in /opt/cleven/compat-wireless and even didn't change permission, only one problem is popup:

The Following User Says Thank You to pawelstryju For This Useful Post:
Bahador

Estel | # 514 | 2012-03-29, 22:31 | Report

It isn't working for me - even enabling drivers at all, in Cleven.

Yet, as You and other guy reported it to be working, maybe it's some user error, on my side. I'll re-check, when times permit. For now, no idea what could went wrong, as new drivers (archive with it) doesn't contain load.sh, so I could not replace it by mistake.

/Estel

The Following 2 Users Say Thank You to Estel For This Useful Post:
fw190, Sourav.dubey

szopin | # 515 | 2012-04-02, 17:27 | Report

Saturn: got a bit time to test reaver. Please add '-N' to how you call it. Two networks I tried reaver on recently gave me repeating same PIN 7-10 times before going forward, average of 16-32 seconds per PIN, with -N got sequential PIN tries and speed up to 3(sometimes even 2) seconds per PIN. Estimated crack time from 30+ hrs down to ~4h.

The Following User Says Thank You to szopin For This Useful Post:
Estel

mr_pingu | # 516 | 2012-04-02, 19:11 | Report

Just asking, szopin: Which revision of reaver do you use? As someone in the reaver thread said r112 wasn't authenticating, in mine case it does but no version helps me as I always get 0x2 error. (even --no-nacks doesn't help) now I want to know if it's the reaver in combination with N900 or just my AP. I don't have another WPS AP

szopin | # 517 | 2012-04-02, 19:19 | Report

Tried on a pub AP as mine was fine without -N and some random driveby. Using 1.4 version got same PIN hammering all the time, with -N it went sequential (most of the time, with occasional hiccups of 2-3 pins repeated, but every 50-80 go sequential)

The Following User Says Thank You to szopin For This Useful Post:
Estel

mr_pingu | # 518 | 2012-04-02, 19:29 | Report

Are you using the binary from the other thread or did you compile it yourself?

IF you did use the binary from the other thread which revision?
If you did compile it yourself, do you mind uploading that revision here?

The Following User Says Thank You to mr_pingu For This Useful Post:
Estel

szopin | # 519 | 2012-04-02, 19:47 | Report

Originally Posted by mr_pingu View Post

Are you using the binary from the other thread or did you compile it yourself?

IF you did use the binary from the other thread which revision?
If you did compile it yourself, do you mind uploading that revision here?

This is my build ondevice, if you wanna try earlier builds let me know. Didn't notice any probs (some people reported better results with 1.3 iirc)

Attached Files

reaver1.4.tar.gz (116.4 KB, 108 views)

The Following 6 Users Say Thank You to szopin For This Useful Post:
Bahador, Estel, g0r, imo, mr_pingu, Sourav.dubey

Saturn | # 520 | 2012-04-04, 23:11 | Report

Originally Posted by szopin View Post

Saturn: got a bit time to test reaver. Please add '-N' to how you call it. Two networks I tried reaver on recently gave me repeating same PIN 7-10 times before going forward, average of 16-32 seconds per PIN, with -N got sequential PIN tries and speed up to 3(sometimes even 2) seconds per PIN. Estimated crack time from 30+ hrs down to ~4h.

Hi szopin,

I haven't tested this but if you need this option (or any other option) it should be fairly easy to add it yourself - it will stay till next update.

open as root the file /opt/cleven/clevenHelper.sh and in line 142 edit the line

Code:

    reaver -i wlan0 -b $2 -a -E -S -v

hope it helps

The Following 7 Users Say Thank You to Saturn For This Useful Post:
Bahador, Estel, fw190, ivgalvez, shockingfm, Sourav.dubey, szopin